Abutments
Mostrando 1-12 de 75 artigos, teses e dissertações.
-
1. Implant Volume Loss, Misfit, Screw Loosening, and Stress In Custom Titanium and Zirconia Abutments
Resumo O objetivo neste estudo foi verificar o efeito da diminuição de volume do implante, desajuste vertical entre o pilar e plataforma protética, torque de afrouxamento do parafuso protético e distribuição da tensão no parafuso em pilares de titânio e zircônia. Dez pilares personalizados de cada material foram fresados e conectados aos implantes d
Braz. Dent. J.. Publicado em: 2020-08
-
2. Influence of Abutment Collar Height and Implant Length on Stress Distribution in Single Crowns
Resumo Este estudo avaliou a influência da altura da porção transmucosa do pilar protético com junção cone morse e do comprimento dos implantes no comportamento biomecânico coroas unitárias com diferentes proporção coroa-implante. Seis modelos virtuais (S11, M11, L11, S13, M13 e L13) foram construídos combinando pilares protéticos com transmucoso
Braz. Dent. J.. Publicado em: 03/06/2019
-
3. Morse taper performance: A finite element analysis study
OBJECTIVES: To evaluate and compare the magnitude and distribution of stresses generated on implants, abutments and first molar metal-ceramic crowns using finite element analysis. METHODS: Preliminary three-dimensional models were created using the computer-aided design software SolidWorks. Stress and strain values were observed for two distinct virtual mo
Clinics. Publicado em: 25/03/2019
-
4. One-year prospective clinical study comparing patient satisfaction and masticatory performance of mandibular overdentures supported by one versus two implants
Abstract There is a lack of clinical evidence on mandibular overdentures (MOD) supported by a single implant. Objective: To compare patient satisfaction and masticatory performance in MOD supported by one versus two implants in a two-group parallel randomized clinical trial. Material and Methods: Twenty-one patients wearing new maxillary and mandibular com
J. Appl. Oral Sci.. Publicado em: 04/10/2018
-
5. Can low-fusing glass application affect the marginal misfit and bond strength of Y-TZP crowns?
Abstract To evaluate the effect of different surface treatments on the marginal misfit and retentive strength between Y-TZP crowns and an epoxy resin. Forty (40) epoxy resin (G10) abutments (height: 5mm, conicity: 60, finish line: large chamfer) with equal dimensions were milled and included in polyurethane to simulate the periodontal ligament. Next, 40 Y-TZ
Braz. oral res.. Publicado em: 07/05/2018
-
6. Short-term quality of life change perceived by patients after transition to mandibular overdentures
Abstract The aim of this longitudinal observational study was to evaluate the oral health-related quality of life (OHRQoL) following patient rehabilitation with implant-retained mandibular overdentures (IMO) and to identify the contribution of the different domains to OHRQoL. The Oral Health Impact Profile (OHIP-EDENT), Dental Impact on Daily Living (DIDL),
Braz. oral res.. Publicado em: 10/03/2017
-
7. Prosthetic abutment influences bone biomechanical behavior of immediately loaded implants
Abstract This study aimed to evaluate the influence of the type of prosthetic abutment associated to different implant connection on bone biomechanical behavior of immediately and delayed loaded implants. Computed tomography-based finite element models comprising a mandible with a single molar implant were created with different types of prosthetic abutment
Braz. oral res.. Publicado em: 31/05/2016
-
8. Effects of different torque levels on the implant-abutment interface in a conical internal connection
Abstract The fit of the implant-abutment interface was assessed by the metallographic technique and by scanning electron microscopy (SEM), using solid abutment types at different torque levels. Forty Morse taper connections and forty solid abutments were used at different torque levels (repeated after 10 minutes) in the following groups (n = 10): 25 Ncm (gro
Braz. oral res.. Publicado em: 15/03/2016
-
9. Failure of prosthetic screws on 971 implants
Abstract Aim: To evaluate the presence of failures in prosthetic screws and whether these failures are related to the type of prosthesis, abutment angulation and presence or not of intermediate. Methods: Two-hundred and sixty-seven patients were evaluated at the Federal University of Santa Catarina, totaling 971 external hexagonal implants in place for at
Braz. J. Oral Sci.. Publicado em: 2015-09
-
10. Influence of Resin Cements on the Tension Force of Cast Frameworks Made by the Technique of Framework Cemented on Prepared Abutments
Este estudo avaliou a força de tração de infraestruturas fundidas confeccionadas pela técnica da infraestrutura cimentada sobre pilares preparados utilizando dois diferentes cimentos resinosos. Quarenta análogos de pilares multi-unit foram individualmente fixados com resina acrílica quimicamente ativada em cilindros de PVC utilizando um delineador.
Braz. Dent. J.. Publicado em: 2015-08
-
11. Compressive Resistance of Abutments with Different Diameters and Transmucosal Heights in Morse-Taper Implants
O objetivo deste estudo foi avaliar a resistência compressiva sob carga oblíqua em pilares com dois diferentes diâmetros e alturas de transmucoso usados para prótese implanto-suportada cimentada em implantes de cone Morse. Quarenta implantes de cone morse foram divididos em quatro grupos com diferentes tamanhos de pilares para próteses cimentadas a fim
Braz. Dent. J.. Publicado em: 2015-04
-
12. Strain analysis of different diameter Morse taper implants under overloading compressive conditions
The aim of this study was to evaluate the amount of deformation from compression caused by different diameters of Morse taper implants and the residual deformation after load removal. Thirty Morse taper implants lacking external threads were divided into 3 groups (n = 10) according to their diameter as follows: 3.5 mm, 4.0 mm and 5.0 mm. Two-piece abutments
Braz. oral res.. Publicado em: 23/01/2015