Aluminum Rolling
Mostrando 1-12 de 19 artigos, teses e dissertações.
-
1. The Effect of Casting Speed and the Fraction of Al5%Ti1%B Inoculant on the Microstructure and Mechanical Properties of the AA5052 Aluminum Alloy Produced by the Direct Chill Process
This study aimed to assess the effect of casting speed and the addition of Al5%Ti1%B inoculant in the casted AA5052 aluminum alloy plate manufactured by the Direct Chill process. The focus of this work was to decrease the rejection index of rolled products due to the occurrence of superficial flaws on plates. These defects impact directly on the production c
Mat. Res.. Publicado em: 01/02/2018
-
2. Study of Cryogenic Rolling of FCC Metals with Different Stacking Fault Energies
Aluminum, copper and silver samples, all of them face-centered cubic (FCC) metals, were rolled at room and cryogenic temperatures until equivalent strains (ε) were between 3.23 and 4.13. The cryogenic temperature (CT) and room temperature (RT) rolled samples were evaluated by hardness tests and X-ray diffraction (XRD), which indicate influence of stacking f
Mat. Res.. Publicado em: 18/12/2017
-
3. Texture, Microstructure and Mechanical Properties of 6111 Aluminum Alloy Subject to Rolling Deformation
The mechanical properties, texture and microstructural evolution of a 6111 aluminum alloy during hot rolling and cold rolling deformation were systematically investigated in this article. The results show that cold rolling and hot rolling have significant effects on the tensile behaviors of the alloy. The shear texture and recrystallization texture mainly fo
Mat. Res.. Publicado em: 31/07/2017
-
4. The Analysis of the Cold Flat Rolling Process by Salf Program
SALF program is a Brazilian program developed to simulate the cold flat rolling process by the finite element method. The program uses the implicit and rigid-plastic approaches to perform numerical analyses. This article presents the cold flat rolling simulations performed by SALF, where the variables of rolling force, effective strain rate, and effective st
Mat. Res.. Publicado em: 23/03/2017
-
5. Study of aluminum nitride precipitation in Fe- 3%Si steel
For good performance of electrical steels it is necessary a high magnetic induction and a low power loss when submitted to cyclic magnetization. A fine dispersion of precipitates is a key requirement in the manufacturing process of Fe- 3%Si grain oriented electrical steel. In the production of high permeability grain oriented steel precipitate particles of c
Mat. Res.. Publicado em: 11/06/2013
-
6. Estudo do comportamento mecânico da liga alumínio cobre 2024 solubilizada e envelhecida para aplicações aeronáuticas
Aluminum alloys present low specific density, good strength, and high corrosion resistance under common environments. Aluminum-Copper 2024 alloy is one of the most widely used alloy in aircraft fuselage structures due to its good mechanical properties. The microstructure of the alloy was observed by optical microscopy showing elongated grains caused from the
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 23/08/2011
-
7. Influência da anisotropia gerada por laminação sobre a medição de tensões por ultrassom em ligas de alumínio 7050 / Influence of anisotropy generated by rolling on the stress measurement by ultrasound in 7050 aluminum alloys
A medição de tensão por ultrassom é baseada no princípio da acustoelasticidade que relaciona a deformação de um corpo submetido a um estado de tensão com a variação da velocidade de propagação de onda no corpo. A relação entre tensão e velocidade de onda é determinada pelo módulo de elasticidade e pela constante acustoelástica. Constantes a
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 08/07/2011
-
8. Texture analysis of cold rolled and annealed aluminum alloy produced by twin-roll casting
A 7.4 mm thick strip of 3003 aluminum alloy produced by the industrial twin-roll casting (TRC) process was homogenized at 500 °C for 12 hours, after which it was cold rolled in two conditions: 1) to reduce the strip's thickness by 67%, and 2) to reduce it by 91%. The alloy was annealed at 400 °C for 1 hour in both conditions. The results revealed that a ro
Materials Research. Publicado em: 22/12/2011
-
9. Numerical and experimental analysis of lubrication in strip cold rolling
In this work an analytical model based on the slab method was built to analyze the lubrication during cold rolling of aluminum strips. Some process variables were studied like the rolling speed, the cross-section reduction, and lubricant viscosity. Numerical results are presented for pressure variation and film thickness at the inlet and work zones. The load
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2011-06
-
10. Estudo comparativo da estampabilidade da liga de aluminio AA1050 partindo de placas obtidas por vazamento direto e bobinas obtidas por vazamento contínuo. / Comparative study of the deep drawing alloy AA1050 from plates obtained by direct casting and coils obtained by continuos casting.
Stampability of aluminum alloys is a subject of interest to several industrial sectors because they are largely used in the fabrication of several parts and components. The choice is based upon the stampability and the relative manufacturing capability in relation to other aluminum alloys that contain larger amounts of alloying elements and, consequently, hi
Publicado em: 2010
-
11. Model to characterize susceptibility to distortions by welding in aluminum plates / Proposta de modelo para caracterizar susceptibilidade a distorção devido a soldagem em chapas de aluminio
The industry interest on having a better control in the distortions provoked by welding of aluminum plates, caused by the crescent demand of this material, motivated the development of this work. In this work, it is studied the deformation caused by TIG welding in aluminum plates, alloy Al 5052, in function of the cold working degree (tempers) on the plates
Publicado em: 2009
-
12. Caracterizações de propriedades microestruturais e mecânicas de ligas AA 1100 e AA 5052 processadas pela técnica de laminação acumulativa ("Accumulated Roll Bonding - ARB"). / Characterization of microestrutural and mechanical properties from AA1100 and AA5052 alloys that were processed by Accumulated Roll Bonding - ARB.
The present work is related to the production, in a laboratory scale, of a metallic microstructure having a grain size smaller than one micrometer, through the Accumulated Roll Bonding technique(ARB), for two different aluminum alloys, namely AA 1100 and AA 5052. The strips obtained by the ARB technique have been characterized by their mechanical properties
Publicado em: 2009