Bearing Steel
Mostrando 1-12 de 31 artigos, teses e dissertações.
-
1. WIND EFFECTS ON FOUNDATIONS OF SILOS AND LIGHT STRUCTURES: SOLUTION BY USE OF STEEL PILES IN DIABASIC SOIL
ABSTRACT Wind solicitations generate horizontal, tensile, and compressive stresses on building foundations. In empty light structures, such as agricultural greenhouses and, in the specific case of silos and elevated structures such as metal water tanks, the consideration of these loads becomes important because the lack of the weight component due to the sto
Eng. Agríc.. Publicado em: 19/06/2019
-
2. Experimental analysis of load capacity in beams with steel fiber reinforcement on the compression face
Resumo A utilização de fibras de aço no concreto visa aumentar principalmente a tenacidade, em função da aderência das fibras à matriz cimentícia. Entretanto como existem diversas tipologias de fibras de aço, as principais diferenças estão no fator de forma (relação entre comprimento e diâmetro), na geometria das fibras, e, na caracterização
Rev. IBRACON Estrut. Mater.. Publicado em: 2019-02
-
3. Fatiga de contacto por rodadura en acero SAE 1050 recubierto con TiN, posteriormente templado
ABSTRACT The use of ceramic coatings of the nitride, carbide, or diamond type on steel substrates promotes the improvement of tribology properties. Nevertheless, high hardness gradients and adhesion problems may deteriorate the performance of these coatings when subjected to Rolling Contact Fatigue (RCF). Some studies on steels with ceramic coatings were car
Matéria (Rio J.). Publicado em: 19/07/2018
-
4. Evolución microestructural in-situ a alta temperatura de depósitos de soldadura de aceros 9Cr con diferentes contenidos de boro
ABSTRACT New alloys have been developed for enhancing the performance of the equipment used in thermoelectric power generation industry. With the objective of increasing the creep resistance of these materials, changes in the content of some microalloying elements were carried out. Boron bearing in creep strength enhanced 9Cr steel (CSE9Cr) welds improved ma
Matéria (Rio J.). Publicado em: 19/07/2018
-
5. Vida a fatiga de uniones soldadas mediante PAW de aceros microaleados al boro
ABSTRACT In the last years microalloyed boron steels have been adopted in the automotive industry to achieve weight reductions. Namely, they are used as load-bearing elements such as pillars and reinforcements, in a quenched and tempered (QT) condition with tensile strength ranging from 800 to 1300 MPa. Dual-Phase (DP) steels have also been introduced in thi
Matéria (Rio J.). Publicado em: 19/07/2018
-
6. Performance of infill stiffened steel panel against blast loading
Abstract In blast loading, out-of-plane behavior of infill wall is activated initially. Contrary to other types of infill wall such as brick or concrete wall, infill steel plate wall exhibits more ductility. Since blast impulsive loading suddenly exerts a large amount of kinematic energy to infill wall, energy absorption characteristic of the infill wall sh
Lat. Am. j. solids struct.. Publicado em: 26/04/2018
-
7. Investigation on Friction and Wear Properties of High-Temperature Bearing Steel 9Cr18Mo
This paper presented a study of friction and wear on 9Cr18Mo when rubbed against other materials (steel-304, steel-440C, steel-GCr15 or silicon nitride ceramic ball) at high temperature conditions. Friction and wear tests were carried out with universal a friction and wear testing machine. The wear morphology was analyzed by a Nanovea three-dimensional profi
Mat. Res.. Publicado em: 05/04/2018
-
8. Thermal analysis of steel-concrete composite cross sections via CS-ASA/FA
Abstract When exposed to high temperatures, such as in a fire situation, the physical and resistance characteristics of the materials employed in the structure deteriorate as the temperature increases. This fact promotes a considerable loss in the bearing capacity and stiffness of the structural system. The verification of a structure exposed to fire depends
REM, Int. Eng. J.. Publicado em: 2018-04
-
9. Effects of Different Plasma Nitrided Layers on the Tribological Performance of DLC Coatings
When multifunctional surface engineering processes that combine purpose-oriented phases are applied to soft substrates, a combination of high wear resistance, high load support and low coefficients of friction can be achieved. In this study, the effects of different nitrided layers on the tribological behaviour of a diamond-like carbon (DLC) film deposited o
Mat. Res.. Publicado em: 12/09/2016
-
10. Effect of Web Holes and Bearing Stiffeners on Flexural-Shear Interaction Strength of Steel Cold-Formed C-Channel Sections
Abstract This paper presents an investigation on interaction equation between the required flexural strength, M, and the required shear strength, V, of cold-formed C-channels with web holes and bearing stiffeners. The primarily shear condition test was employed to study total 8 back to back lipped C channel sections of 95 and 100 mm depth when bearing stiffe
Lat. Am. j. solids struct.. Publicado em: 2016-06
-
11. Graphite and Nickel Containing Tin Bronze-Steel Bimetals as Lead Free Bearing Materials
Ni was added into graphite-lead free tin bronze composite layers on surface of steel sheets by primary sintering mixed powders of graphite and CuSn10 with addition of a nickel nitrate and poly(vinyl alcohol) (PVA) solution in an ammonia decomposition atmosphere. The reduced Ni particles attached on the surface of graphite and CuSn10 particles help to link th
Mat. Res.. Publicado em: 20/05/2016
-
12. Evaluation and comparison of behavior of corrugated steel plate shear walls
In this paper, the nonlinear behaviour of steel plate shear walls with corrugated plates under lateral pushover loading conditions in the models' top level has been analytically investigated by the finite element method. The one-storey frames have beams and columns as boundary elements. Steel plate shear walls are simulated using the finite element method, b
Lat. Am. j. solids struct.. Publicado em: 2015-08