Capillary Absorption
Mostrando 1-12 de 56 artigos, teses e dissertações.
-
1. Methodology for evaluation of the influence of roughness and capillary absorption of ceramic blocks on the render’s tensile bond strength
Abstract The literature indicates that it is difficult or even impossible to associate with strong statistical confidence the bond strength of a mortar coating with the properties of the ceramic block, such as roughness and water absorption. In this work, it is assumed that the variability in capillary water absorption and roughness, and the use of methods t
Cerâmica. Publicado em: 2022
-
2. Influence of the physical characteristics of sand and the crushed filler content on the properties of self-leveling mortars
Abstract The properties of self-leveling mortars (SLMs) in the fresh and hardened state are strongly affected by their formulation. In this study, the influence of three different quartz sands (different physical characteristics) was investigated in SLMs, as well as the replacement of these sands by crushed basalt filler. The tests performed were: spreading,
Cerâmica. Publicado em: 2021-06
-
3. Shrinkage and porosity in concretes produced with recycled concrete aggregate and rice husk ash
Resumo O emprego de agregado reciclado de concreto (ARC) para a produção de novos concretos é uma alternativa interessante para mitigar impactos ambientais. O ARC pode aumentar a porosidade e impactar negativamente as propriedades do concreto. A cinza de casca de arroz (CCA), empregada como material cimentício suplementar, pode mitigar estes efeitos. Est
Rev. IBRACON Estrut. Mater.. Publicado em: 18/07/2019
-
4. Estudo das propriedades de concretos com adição de fibras vegetais e de polipropileno para uso em paredes estruturais
RESUMO Estudou-se neste trabalho as propriedades de concretos com adição de fibras vegetais (sisal e rami) e de polipropileno para uso em paredes estruturais. Realizou-se uma comparação do desempenho do concreto com a adição de fibras vegetais e de fibra de polipropileno, a fim de se verificar a possível substituição. Foram avaliadas a retração po
Matéria (Rio J.). Publicado em: 10/06/2019
-
5. DETERMINATION OF Cu, Fe, Mn, Zn AND FREE FATTY ACIDS IN PEQUI OIL
Pequi (Caryocar brasiliense Camb.), a typical fruit of the Brazilian Cerrado, is an important source of micronutrients and fatty acids. In this work, a new approach for the acid digestion (using H2SO4, HNO3 and H2O2) of pequi oil samples and the determination of Cu, Fe, Zn and Mn by flame atomic absorption spectrometry (F AAS) was employed. Capillary zone el
Quím. Nova. Publicado em: 2016-06
-
6. Exploring the Versatility of an Atomic Absorption Spectrometer: Application to Direct Molecular Determination of Caffeine and Propranolol
A simple strategy using an atomic absorption spectrometer (AAS) for the direct determination of molecular compounds is proposed. The determination of caffeine and propranolol employing atomic absorption instrumentation was conducted, monitoring the emission lines of Fe (271.9 nm) and Mg (285.2 nm), respectively, using a quartz cuvette (1.0 cm) positioned in
J. Braz. Chem. Soc.. Publicado em: 2016-04
-
7. Durability Enhancement Of SCC With Waste Glass Powder
Self compacting concrete (SCC) requires a large quantity of fine materials compared to common concrete. In this work waste glass powder was used to replace (50%) of filler required. Two types of SCC were manufactured, a control SCC type (CTL) using cement and limestone filler and another with glass powder replacing 50% of the filler. Mechanical and durabilit
Mat. Res.. Publicado em: 19/02/2016
-
8. Ampliação do uso da técnica de espectrometria de absorção atômica utilizando tubo metálico na chama para determinação de prata / Enlarging the use of thermospray flame furnace atomic absorption spectrometry for determination of silver
Thermospray flame furnace atomic absorption spectrometry (TS-FF-AAS) uses a metallic tube on the flame of the atomic absorption spectrometer. The sample is introduced in the tube by a ceramic capillary. In the development of this method, the parameters involved were studied and the optimal conditions consist of using air as carrier at 0.4 mL min, 200 mL of s
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 09/03/2012
-
9. Polyamide worm gear: manufacturing and performance
The focus of this paper is to establish a characterisation method for seven polyamide (PA) grades to determine the major material to manufacture an automotive worm gear. The composite properties were measured according to the worm gear loadings: tensile strength, Young's modulus, abrasion and impact resistance. They were also correlated to the PA moisture ab
Materials Research. Publicado em: 07/06/2012
-
10. INFLUÊNCIA DE MATERIAIS DE PROTEÇÃO SUPERCIAL NA RESISTIVIDADE ELÉTRICA E ABSORÇÃO CAPILAR DO CONCRETO / INFLUENCE OF SUPERFICIAL PROTECTION MATERIALS IN ELECTRICAL RESISTIVITY AND CAPILLARY ABSORPTION OF CONCRETE
A durabilidade das estruturas de concreto armado é resultado da ação protetora do concreto sobre a armadura. Quando a passivação do aço deixa de existir a estrutura torna-se vulnerável ao fenômeno da corrosão, cuja propagação, após iniciada é essencialmente controlada pela resistividade elétrica do concreto. Outro fator importante na durabilida
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 24/01/2011
-
11. Chloride diffusivity in red mud-ordinary portland cement concrete determined by migration tests
Red mud, which is a solid waste produced in the alumina production process, is classified as dangerous due to its high pH. In this work, the concentration of chlorides was monitored by measuring the conductivity of the anolyte, which initially was distilled water. The steady and nonsteady-state chloride diffusion coefficients were estimated from the "time la
Mat. Res.. Publicado em: 06/05/2011
-
12. Contribution to the development of performance specifications for concretes containing blast furnace slag / Contribuição ao desenvolvimento de especificações por desempenho para concretos com escoria de alto-forno
In 2008 alone, the annual steel production in Brazil was around 31 million tons. The steel production process generates an average of 500 kg of residues and co-products per ton of steel. From this total, 70% corresponds to the slags. Although investigating the increase of blast furnace slag use is of extreme importance for the concrete and steel industries s
Publicado em: 2010