Cement And Quartz
Mostrando 1-12 de 26 artigos, teses e dissertações.
-
1. Evaluation of the use of silica-alumina refractory waste as a supplementary cementitious material
Abstract The use of supplementary cementitious materials (SMCs) is one of the three essential factors for the sustainability of the cement industry. To reduce CO2 emissions, several studies have introduced new methods for the utilization of industrial wastes such as the addition into cementitious materials. The objectives of this study were to chemically and
Cerâmica. Publicado em: 2021-06
-
2. Reuse of iron ore tailings in the production of geopolymer mortars
Abstract A great variety of silica and alumina-rich materials have been investigated in the production of alkaline activated binders (or geopolymers) with low environment impact, e.g. low CO2 emissions. Geopolymer mortars and concretes may be more environmentally friendly if not only Portland cement but also natural aggregates (sand, gravel) are replaced wit
REM, Int. Eng. J.. Publicado em: 16/09/2019
-
3. Investigación de diseños de mezcla para producir Ultra High Performance Fiber Reinforced Concrete (UHPFRC) usando ANOVA
ABSTRACT An experimental study is presented to produce Ultra High Performance Fiber Reinforced Concrete (UHPFRC) including industrial waste in the mix, and determine the average compressive strength. The study includes factor arrangements to perform analysis of variance using ANOVA. The controllable factors were: (i) age of the sample; (ii) granulometry of t
Matéria (Rio J.). Publicado em: 10/06/2019
-
4. Potential Slow Release Fertilizers and Acid Soil Conditioners Obtained by One-Pot Mechanochemical Activation of Chrysotile:Cement Roofing Sheets with K2HPO4
Chrysotile:cement roofing sheets were milled with and without K2HPO4. As indicated by X-ray diffraction (XRD), the samples crystallinities were reduced with the increasing milling time. The same tendency was observed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM), with disaggregation of the chrysotile fiber bundles and forma
J. Braz. Chem. Soc.. Publicado em: 2019-02
-
5. Physicochemical Characterization of Pulverized Phyllite Rock for Geopolymer Resin Synthesis
Geopolymeric materials have some unique properties such as early-high compressive strength, durability, resistance to acids and sulfates, ability to immobilize toxic and radioactive compounds, low porosity and high temperature resistance. These materials are strategic for sustainable development and are a suitable alternative to Portland cement. The use of p
Mat. Res.. Publicado em: 06/07/2017
-
6. Microstructure and hardness of cement pastes with mineral admixture
ABSTRACT Portland cement pastes are highly heterogeneous material and exhibits heterogeneous features over a wide range of length scales. Mechanical properties of microstructure can be determined using depth-sensing indentation. Coupled indentation/SEM technique can be used to location the indents and provides a way to determine the mechanical properties of
Matéria (Rio J.). Publicado em: 22/06/2017
-
7. Effect of different composite core materials on fracture resistance of endodontically treated teeth restored with FRC posts
Abstract Objective This study evaluated the fracture resistance of endodontically treated teeth restored with fiber reinforced composite posts, using three resin composite core build-up materials, (Clearfil Photo Core (CPC), MultiCore Flow (MCF), and LuxaCore Z-Dual (LCZ)), and a nanohybrid composite, (Tetric N-Ceram (TNC)). Material and Methods Forty en
J. Appl. Oral Sci.. Publicado em: 2017-04
-
8. Characterization of basic oxygen furnace slag and granite waste mixtures to Portland cement production
Abstract The aim of this paper is to analyze mixtures of basic oxygen furnace slag and granite waste in order to produce Portland cement. X-ray patterns were carried out in both the basic oxygen furnace slag and granite waste. Then, mixtures were prepared to obtain the binary basicity of 0.5, 0.9 and 1.2. The mixtures were melted at 1500ºC. Two cooling step
REM, Int. Eng. J.. Publicado em: 2016-12
-
9. Estudo de métodos visando à análise direta de alumina, cimento e quartzo em ICP OES / Studies of methods aiming the direct analysis of alumina, cement and quartz by ICP OES
O objetivo deste estudo foi avaliar parâmetros para o desenvolvimento de métodos visando à determinação elementar em alumina, cimento e quartzo por espectrometria de emissão óptica com plasma indutivamente acoplado (ICP OES) com amostragem de suspensão. Alguns elementos foram investigados como possíveis candidatos a padrões internos (PIs) Be, Dy, G
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 29/07/2011
-
10. Effect of different light curing methods on mechanical and physical properties of resin-cements polymerized through ceramic discs
OBJECTIVE: The aim of this study was to compare the polimerization ability of three different light-curing units (quartz tungsten halogen, light-emitting diodes and plasma arc) and their exposure modes (high-intensity and soft-start) by determination of microhardness, water sorption and solubility, and diametral tensile strength of 5 dual-curing resin cement
J. Appl. Oral Sci.. Publicado em: 01/07/2011
-
11. Hardening of a dual-cure resin cement using QTH and LED curing units
OBJECTIVE: This study evaluated the surface hardness of a resin cement (RelyX ARC) photoactivated through indirect composite resin (Cristobal) disks of different thicknesses using either a light-emitting diode (LED) or quartz tungsten halogen (QTH) light source. MATERIAL AND METHODS: Eighteen resin cement specimens were prepared and divided into 6 groups acc
Journal of Applied Oral Science. Publicado em: 2010-04
-
12. Influence of storage times on bond strength of resin cements to root canal
The resin cements are responsible to retention of the indirect materials decreasing marginal leakage, increasing failure resistance compared with conventional cementation. The cementation within root canal is very hard due unfavorable conditions regarding the application of adhesive techniques caused by inadequate access. Therefore, considering the possibili
Materials Research. Publicado em: 2010-03