Ceramics Properties
Mostrando 1-12 de 185 artigos, teses e dissertações.
-
1. Properties and technical characteristics of Casira pottery, Jujuy, Argentina
Abstract In this work, the results of a multi-technique characterization of a type of pottery production with high cultural and economic relevance from the only potter town in Argentina are presented and correlated. Raw materials, a prepared paste, and ceramic samples were studied. Chemical, structural, textural, microstructural, and thermal features were as
Cerâmica. Publicado em: 2022
-
2. Thermoelectric properties of barium doped calcium cobaltite obtained by simplified chemical route
Abstract Calcium cobaltite (CCO) thermoelectric ceramics in Ca3Co4O9 and Ca2.95Ba0.05Co4O9 compositions were produced by a simplified chemical route developed in this study. Undoped ceramics sintered at 1193 K for 12 h presented a bulk density equivalent to 77% of the theoretical density, one of the highest values ever found for conventionally sintered undop
Cerâmica. Publicado em: 2021-03
-
3. Influence of sintering parameters on the microstructure and mechanical properties of nanosized 3Y-TZP ceramics
Abstract The fracture toughness of 3Y-TZP ceramics obtained from a nanocrystalline powder with an optimized microstructure and highly transformable tetragonal grains was investigated. Samples of ZrO2-3 mol% Y2O3 were sintered at temperatures between 1250 and 1400 °C, with isothermal holding times of up to 16 h. Samples sintered at 1250 °C exhibited relativ
Cerâmica. Publicado em: 2021-03
-
4. Freeze-casting applied to ceramic materials: a short review of the influence of processing parameters
Abstract In recent years there is a high interest in the freeze-casting process because it is a simple, economical, and environmentally friendly method for obtaining highly porous materials. Most of the materials obtained by this technique have directional pore structure and anisotropic properties. However, a wide range of pore size and morphology can be obt
Cerâmica. Publicado em: 2021-03
-
5. Cold sintering and electric characterization of ZnO-BaTiO3 composites
Abstract The sintering is an essential step in the processing of ceramics materials. A number of researchers have reported new techniques for sintering. However, in general, the process still demands high temperatures. This paper reports the results of the cold sintering of ZnO-BaTiO3 composites. The microstructural, structural, and electric properties of th
Cerâmica. Publicado em: 2021-03
-
6. Serpentinites: Mineral Structure, Properties and Technological Applications
Serpentine is a versatile mineral family rich in Mg silicate with several polymorphic phases, mainly antigorite and lizardite, all of them with similar chemical composition (Mg3Si2O5(OH)4). Their structures are generally composed of octahedral layers rich in Mg[MgO2(OH)4]6- , attached to a tetrahedral silicate [Si2O5]2- sheet. The unique physicochemical prop
J. Braz. Chem. Soc.. Publicado em: 2020-01
-
7. Evaluation of the Effect of the Incorporation of Blends of Fuel and Fluxing Wastes in Red Clay Ceramics
The clay samples endure the incorporation of industrial and urban wastes, which do not cause large variations in their properties if added in controlled quantities. Wastes can be classified as fuel, fluxing and property affecting wastes. The fuel wastes usually have a high amount of organic matter, that when heated cause exothermic reactions, releasing heat
Mat. Res.. Publicado em: 09/12/2019
-
8. Study of Structural and Electric Properties of the PZT 52/48 Doped With Er+3
The scientific community has shown a growing interest in relating to the ferroelectric materials and it has made an effort to develop them. Among these several ferroelectric materials, we proposed to investigated Pb(ZrTi)O3 doped with distinct Er+3 concentrations. Our aim was to investigate how the erbium affects the PZT electrical properties. To determine t
Mat. Res.. Publicado em: 25/11/2019
-
9. Efeito da adição de resíduo de vidro em massa de cerâmica de alvenaria
RESUMO Este trabalho investigou o efeito da adição de resíduo de vidro para fabricação de cerâmica de alvenaria. Foram conformados corpos-de-prova cilíndricos de 27 mm de diâmetro por 45 mm de altura, a partir da massa padrão de uma indústria de cerâmica vermelha e outras 3 formulações (5, 10 e 20%) com incorporação de vidro, baseado em estudo
Matéria (Rio J.). Publicado em: 25/11/2019
-
10. Restorative Possibilities Using Zirconia Ceramics for Single Crowns
Resumo Dois casos clínicos são apresentados para explorar as diferenças técnicas e discutir as vantagens e desvantagens de se utilizar zircônia com cerâmica estratificada ou monolítica para confeccionar coroas unitárias. O primeiro caso descreve os passos clínicos na confecção de uma coroa monolítica no segundo pré-molar esquerdo utilizando uma
Braz. Dent. J.. Publicado em: 07/10/2019
-
11. Investigation on Electrical Properties and Microdefects of Nb5+-Doped BaTiO3 Based Ceramics by Positron Annihilation Techniques
The influence of the Nb5+-doped content and the doping CaCO3 on the electrical properties and the microdefects of BSTN ceramics by Positron Annihilation Techniques were studied, which were fired at 1350 ºC for 2 hours in air. The PTCR characteristics in the BSTN samples were also investigated. Moreover, the information on microdefects in BSTN ceramics was d
Mat. Res.. Publicado em: 23/09/2019
-
12. Influence of Sintering Time on the PTCR Effect of Nb2O5-doped BaTiO3 Ceramics
The effects of the sintering time on the electrical properties and the positive temperature coefficient of resistance (PTCR) effect of Ba1.006(Ti1-xNbx)O3 (BTN) ceramics were investigated, which were sintered at 1190 ºC for 0.5-6 hours in a reducing atmosphere and then re-oxidized at 800 ºC for 1 hour. The results indicated that the sintering time affected
Mat. Res.. Publicado em: 16/09/2019