Continuous Simulation
Mostrando 1-12 de 190 artigos, teses e dissertações.
-
1. Identifying patient safety competences among anesthesiology residents: systematic review
Abstract Introduction and objective Patient safety is a concept of great importance to managers, health professionals, and patients and their families, given patient safety promotes more effective care and reduces costs. Moreover, while analyzing the area of anesthesiology, one can realize the epidemiological changes, increased complexity and number of proc
Brazilian Journal of Anesthesiology. Publicado em: 2022
-
2. FEM-DEM simulation of Uniaxial Compressive Strength (UCS) laboratory tests
Abstract Finite/discrete element methods (FDEM) are hybrid numerical models that use algorithms to analyze the transition from continuous to discontinuous. This type of formulation allows modeling physical laboratory tests with greater proximity to reality. This article proposes to simulate the average behavior of a uniaxial compression test campaign. The te
REM, Int. Eng. J.. Publicado em: 2020-12
-
3. Editorial Comment: Development and validation a task-specific checklist for a microsurgical varicocelectomy simulation model
ABSTRACT Introduction: Transverse preputial island flap urethroplasty (TPIFU) is one of the most frequently performed technique for single-stage repair in proximal hypospadias. It was reported that the subepithelial urethroplasty would obviously decrease urethrocutaneous fistula (UF) complication after proximal TIP. But in the process of TPIFU, it had not b
Int. braz j urol.. Publicado em: 2020-10
-
4. High Efficiency Continuous Inverse Class-F Power Amplifier with Modified Current Waveform
Abstract Continuous inverse class-F (CICF) is a recent mode of harmonically-tuned RF power amplifiers used to extend the operating bandwidth of the conventional narrowband class-F−1 power amplifier by producing variable set of drain current waveforms and load admittances that give the same operating efficiency. In this work, a new approach of analysis is d
J. Microw. Optoelectron. Electromagn. Appl.. Publicado em: 2020-09
-
5. HYBRID SYSTEM SIMULATION TO SUPPLY HEATED AIR TO A SOLAR FOOD DRYER
ABSTRACT The intermittence of solar radiation, due to continuous rainy or cloudy days, is a limitation of simple and small solar dryers. These conditions often make them impossible to use. By including storage systems (thermal accumulation) and/or auxiliary energy sources, drying processes or dehydration can be conducted continuously, even during periods of
Eng. Agríc.. Publicado em: 2020-04
-
6. Intermittent vibrations accelerate fracture healing in sheep
Abstract Purpose: To investigate the effect of intermittent vibration at different intervals on bone fracture healing and optimize the vibration interval. Methods: Ninety sheep were randomized to receive no treatment (the control group), incision only (the sham control group), internal fixation with or without metatarsal fracture (the internal fixation gro
Acta Cir. Bras.. Publicado em: 12/09/2019
-
7. Reduction of epistemic uncertainty of a crash box model - experimental and numerical investigations
Abstract The high prediction accuracy of FEM calculations is an important prerequisite for their growing use in the field of crash load cases for vehicle body design. Although the simulation accuracy of crash calculations for steel structures already is at a high standard, continuous improvements and a further development of the simulation models are crucial
Lat. Am. j. solids struct.. Publicado em: 21/03/2019
-
8. Estimating design hydrographs at the basin scale: from event-based to continuous hydrological simulation
RESUMO Hidrogramas de projeto são amplamente utilizados em engenharia hidrológica. Típicas aplicações adotam métodos baseados em eventos (EB), utilizando modelos chuva-vazão para converter hietogramas de projeto em hidrogramas. Incertezas incluem a definição de condições antecedentes e a premissa de equivalência entre tempos de retorno da chuva
RBRH. Publicado em: 18/02/2019
-
9. Generation of Electrical Energy Obtained Through a Continuous Current Generator Coupled to the Pedal of an Ergometric Bicycle
ABSTRACT This study presents a system of conversion of mechanical energy produced by physical activity into electric energy obtained by a CC generator coupled to the pedal of an ergometric bicycle. It presents the converter that will be used to adjust the voltage and power coming from the system, as well as the details of the converter design, the simulation
Braz. arch. biol. technol.. Publicado em: 29/11/2018
-
10. Simulación matemática para la optimización del patrón de flujo entregado por una buza para el molde de colada continua de planchón delgado
ABSTRACT Understanding the behavior of the oscillations of the jets into the mold of thin slab funnel is essential to ensure a constant supply of liquid steel, improve control of the flow patterns and consequently increase plant productivity and the final product quality. To achieve this, we conducted a study of the effect of the internal design of the nozzl
Matéria (Rio J.). Publicado em: 19/07/2018
-
11. Finite element simulation of fracture in a restored premolar tooth using high aspect ratio elements
Abstract Introduction The term cracked tooth syndrome refers to an incomplete fracture of a vital posterior tooth that involves the dentin and occasionally extends into the pulp. There is a very limited number of publications trying to model dentin crack growth using numerical techniques. Therefore, it is essential to numerically model this phenomenon in o
Res. Biomed. Eng.. Publicado em: 19/03/2018
-
12. Computational Investigation on the Effects of Two-Way Wing Morphing Strategy in the Critical Mach Number
ABSTRACT: The elasto-flexible wing morphing is an advanced methodology to achieve higher lift-to-drag (L/D) ratio for the subsonic wing configurations at the given flow conditions. The present article describes mechanisms of continuous morphing of a swept back wing for achieving effective delay in the critical Mach number (Mcr) distribution over the wing sur
J. Aerosp. Technol. Manag.. Publicado em: 08/03/2018