Cooling Grain
Mostrando 1-12 de 49 artigos, teses e dissertações.
-
1. Effect of LZSA glass-ceramic addition on the erosive wear of pressureless sintered alumina
Abstract This study aims to evaluate the influence of the 11.6Li2O-16.8ZrO2-68.2SiO2-3.4Al2O3 (mol%) glass-ceramic addition (LZSA, 7 to 21 vol%) on the erosive wear of alumina in comparison to values of pure alumina obtained from the literature. Thus, composites were prepared from three commercial alumina of different initial particle sizes. Specimens were o
REM, Int. Eng. J.. Publicado em: 2020-06
-
2. Austenitic Grain Size Prediction in Hot Forging of a 20MnCr5 Steel by Numerical Simulation Using the JMAK Model for Industrial Applications
Yield strength and toughness in steels are directly associated with hot forging processes, especially by controlling austenitic grain size and cooling conditions. The phenomenological JMAK model in macroscale has been applied in different material classes to predict grain size after hot forming. However, on an industrial application, there is still a lack of
Mat. Res.. Publicado em: 05/12/2019
-
3. Characterization of Austenite Decomposition in Steels with Different Chemical Concepts and High Potential to Manufacture Seamed Pipes for Oil and Gas Industry
This work presents the characterization of austenite decomposition kinetics in two steels during continuous cooling considering non-deformed austenite grains. Two different chemical concepts of steels were evaluated: low carbon - high manganese and a relatively new concept based on low carbon - low manganese - high niobium contents. Dilatometric experiments,
Mat. Res.. Publicado em: 21/10/2019
-
4. Proposição de um Modelo Empírico para Determinação das Temperaturas Críticas Durante Resfriamento Contínuo em Zonas Termicamente Afetadas de Aços IF Soldados pelo Processo TIG
Resumo Aços IF são amplamente empregados na indústria automobilística. No decorrer das aplicações de soldagem, eles passam pela transformação de fase austenita (γ) → ferrita (α) que ocorre por nucleação e crescimento de grão e, em condições isotérmicas, é descrita pela equação JMAK. Todavia, as transformações de fases pós-soldagem ac
Soldag. insp.. Publicado em: 23/09/2019
-
5. Avaliação da susceptibilidade à corrosão de um aço inoxidável AISI 316L submetido à simulação térmica com o uso da Gleeble
RESUMO Este trabalho teve como finalidade avaliar a influência do tamanho médio dos grãos na susceptibilidade à corrosão do aço inoxidável austenítico AISI 316L, cujo material é bastante utilizado em juntas soldadas, em temperatura ambiente e em baixíssimas temperaturas (condições criogênicas) por apresentar excelente resistência à corrosão e
Matéria (Rio J.). Publicado em: 16/09/2019
-
6. Diameter Dependence of Magnetic Properties of Co-based Metal Fibers
Naked Co68.25Fe4.5Si12.25B15 metal fibers with diameter from 25 µm to 100 µm are produced by melt extraction method. Significant diameter dependence of magnetic properties is studied. Their microstructure and magnetic properties of hysteresis loops and giant magneto impedance (GMI) effect at frequencies from 0.1MHz to13MHz are investigated. The results sho
Mat. Res.. Publicado em: 09/09/2019
-
7. Behaviors of Embrittlement and Softening in Heat Affected Zone of High Strength X90 Pipeline Steels
Abstract The embrittlement and softening behaviors in heat affected zone of X90 pipeline steel were studied, and the influence of weld thermal cycle on microstructure and mechanical properties were discussed by combining the effect of peak temperature on the phase transition point (Ar3). Results show that there are embrittlement and softening zones existed i
Soldag. insp.. Publicado em: 15/08/2019
-
8. Influência do Regime Transiente Sobre a Microdureza e Microestrutura nos Aços ASTM-A36 e SAE-1045 Soldados pelo Processo MAG
Resumo O regime quase-estacionário pode não ser alcançado em soldagens a arco elétrico de peças de pequenas dimensões e/ou de materiais de maior condutividade térmica. Entretanto, o regime transiente sempre ocorrerá no início e no final da soldagem. Neste regime, a variação do fluxo de energia via calor pode promover variações microestruturais e
Soldag. insp.. Publicado em: 08/08/2019
-
9. Influência do Ciclo Térmico de Soldagem no Crescimento de Grão, nas Transformações Microestruturais e na Formação de MA na GGZAC de aço TMCP
Resumo A soldagem com elevado aporte térmico é uma das alternativas adotadas pelos estaleiros e fabricantes de torres eólicas para aumento da produtividade. No entanto, os ciclos térmicos gerados no processo podem provocar transformações microestruturais prejudiciais à tenacidade na zona afetada pelo calor, especialmente na região de grãos grosseiro
Soldag. insp.. Publicado em: 09/05/2019
-
10. Damping of Fe-Al Alloy Electrodeposited in an Ionic Liquid
Iron-Aluminium alloys were produced by the electro-deposition of iron-aluminium on a copper substrate. The electro-deposition process was done in the ionic liquid 1-butyl-1-methylpyrrolidinium trifluoromethylsulfonate, [Py1,4]TfO. A solution of (0.2 M FeCl2 + 2.75 M AlCl3)/ [Py1,4] TfO was used at a temperature of T=363 K because this mixture is solid at roo
Mat. Res.. Publicado em: 11/10/2018
-
11. Estudio de la microestructura de un cordón de soldadura de un acero P91 mediante microscopía electrónica de transmisión
ABSTRACT In the present work the microstructural characterization of a single-pass weld of 9Cr1MoVNb P91 steel performed by the flux-cored arc welding (FCAW) process in the “as welding” condition has been carried out by means of transmission electron microscopy. P91 steel offers a good weldability, but the mechanical properties of the welded joints are f
Matéria (Rio J.). Publicado em: 19/07/2018
-
12. Impact of Alloy Composition and Thermal Stabilization on Martensitic Phase Transformation Structures in CuAlMn Shape Memory Alloys
Alloys of CuAlMn are known as cheap, high strength shape memory alloys with an excellent damping capacity within their austenitic-martensitic phase transformation, compared to alloy systems like NiTi, CuZnAl or MnCu. But CuAlMn alloys have disadvantage due to generation of voids by a high shrinkage which further increases the existing proneness to stress cra
Mat. Res.. Publicado em: 19/07/2018