Cutting Forces
Mostrando 1-12 de 51 artigos, teses e dissertações.
-
1. Surface Integrity Analisys in the Hard Turning of Cemented Steel AISI 4317
This work was based on the surface integrity analysis of hardened steel, AISI 4317 case carburized, quenched and tempered with 58 HRC, obtained by a turning operation executed with CBN (cubic boron nitride) tool, varying three basic cutting parameters (cutting speed, feed rate and cutting depth). The surface integrity characterization was conducted analyzing
Mat. Res.. Publicado em: 26/07/2018
-
2. Simulation of the mechanical process of gypsum cutting with picks
Abstract Several research works have been done to assess the effect of the cutting depth on the cutting forces when using picks. In this case, the cutting tests need im-portant equipment to cut rocks, to register the cutting force and to determine the cutting force value. The purpose of this research work is to simulate the laboratory rock cutting tests to d
REM, Int. Eng. J.. Publicado em: 2018-07
-
3. On the Machinability and Surface Finish of Superalloy GH909 Under Dry Cutting Conditions
GH 909 alloy is a kind of low thermal expansion superalloy with high strength and low expansion coefficient. It is mainly used for manufacturing of aero-engine turbine casings, sealing ring, vanes and other gap control parts, to improve the working efficiency and thrust of the engine as well as to reduce gas loss and fuel consumption. However, the machinabil
Mat. Res.. Publicado em: 21/05/2018
-
4. Surface Integrity Analysis in Machining of Hardened AISI 4140 Steel
This study aimed to analyze the residual stresses and roughness in finishing milling of AISI 4140 steel, quenched and tempered up to hardness of 58 HRC. Machining operations were performed with the use of CBN inserts and by varying three basic cutting parameters (cutting speed, feed per tooth and cutting depth). Hardened materials are typically machined by a
Mat. Res.. Publicado em: 23/01/2017
-
5. Emprego de ferramentas estatísticas para avaliação da usinabilidade de ligas de alumínio
The main objective of the present work is to study the effect of the input variables: mechanical properties of the workpiece (tensile strength, hardness and elongation) and cutting conditions (cutting speed, feed rate, depth of cut and lubri-cooling system) over the output variables: cutting forces, power consumption, cutting temperature, surface roughness (
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 28/05/2012
-
6. Influência do teor de silício na usinabilidade da liga de alumínio 6351 - avaliada através de força de corte e acabamento superficial / Influence of the silicon content in the machinability of the 6351 aluminium alloy analysed through cutting force and surface finish
The aim of this work is to study the effect of silicon content in the machinability of CBAs (Compania Brasileira de Aluminio) 6351 aluminum alloy measured through cutting force and surface finish. In a first moment the effect of depth of cut (ap), cutting speed (vc), feed rate (f) and silicon content (% Si) on the machinability were investigated. The machini
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 14/03/2012
-
7. Estudo da influência da força de corte em usinagem a verde nas propriedades mecânicas de cerâmicas sinterizadas / Influence of the cutting force of green machining on the mechanical properties of sintered ceramics
The present study deals with the measurement forces of green machining ceramics and their correlation with the mechanical properties after sintering. The green machining is employed in crude compacts either to check raw formats without compromising the extreme dimensional accuracy or to obtain a preform prior to finish machining after sintering, extensively
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 13/01/2012
-
8. Slip-line metal cutting model with negative rake angle
A small dead region is seen in front of the rake face of the tool during cutting with negative rake. The lack of knowledge about the stagnant region in the cutting with negative rake requires researching new models. In this work, cutting mechanism of the metal cutting with negative rake angle tools and the stagnation zone formation were studied. A model was
J. Braz. Soc. Mech. Sci. & Eng.. Publicado em: 2012-09
-
9. Machinability study of steels in precision orthogonal cutting
The miniaturization of components and systems is advancing steadily in many areas of engineering. Consequently, micro-machining is becoming an important manufacture technology due to the increasing demand for miniaturized products in recent years. Precision machining aims the production of advanced components with high dimensional accuracy and acceptable sur
Materials Research. Publicado em: 03/07/2012
-
10. An analysis of the machinability of ASTM grades 2 and 3 austempered ductile iron
Austempered Ductile Iron (ADI) is a ferrous material that was first fabricated in the second half of last century, therefore a relatively new material compared to steel, which has been used for different applications by mankind for some millennia now. ADI ;s mechanical properties, such as its strength-to-weight ratio, which has proven to outperform that of f
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 22/08/2011
-
11. Efeito do ângulo da fieira na geometria e propriedades mecânicas de barras trefiladas
In cold drawing of metallic bars most of the plastic flow is caused by compressive forces which arise from the reaction of the metal to the die. Due to the characteristics of the process this flow is not homogeneous along the cross section of the bar and is influenced by the die geometry. This inhomogeneous deformation generates residual stresses in the bars
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 18/03/2011
-
12. Estudo das forças, vibrações e desgaste das ferramentas no fresamento da liga de titânio Ti-6A1-4V / A study about forces, vibration and tool wear in Ti-6A1-4V titanium alloy face milling
Ligas de titânio já apresentam um papel de grande importância na indústria aeroespacial, petroquímica e de biomateriais. A combinação de alta resistência mecânica, baixa densidade, resistência à corrosão, biocompatibilidade, boa tolerância tecidual e manutenção de suas características em altas temperaturas, configuram o titânio como um mater
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 07/02/2011