Cyclic Load
Mostrando 1-12 de 47 artigos, teses e dissertações.
-
1. Enhancement the Fatigue Life of Floating Breakwater Mooring System Using Tuned Liquid Column Damper
Abstract Safety is a key design criterion for floating structures. A high rate of mooring accidents has been reported over the past decades. Preventing mooring line failure is a key design objective for floating breakwater systems. The mooring system comprises sets of mooring lines anchored to the seabed. These components are exposed to highly cyclic nonline
Lat. Am. j. solids struct.. Publicado em: 22/08/2019
-
2. Seismic Upgrading of Exterior Reinforced Concrete Frame with Small Column and Joint Area Using Externally Attached Steel Column
Abstract This paper presents cyclic load test of five exterior reinforced concrete frames. All the specimens represent a substandard single-span, low-rise reinforced concrete frame building which behaves a weak column-strong beam mechanism under a strong seismic loading. The first three exterior frames M1, M2 and M3 were designed for the joint shear critical
Lat. Am. j. solids struct.. Publicado em: 10/07/2019
-
3. Fatigue survival and damage modes of lithium disilicate and resin nanoceramic crowns
Abstract Polymer-based composite materials have been proposed as an alternative for single unit restorations, due to their resilient and shock absorbing behavior, in contrast to the brittleness of ceramic materials that could result in failure by fracture. Objective: To evaluate the fatigue strength and damage modes of monolithic posterior resin nanoceramic
J. Appl. Oral Sci.. Publicado em: 30/05/2019
-
4. Acute exercise inhibits gastric emptying of liquids in rats: influence of the NO-cGMP pathway
We previously found that acute exercise inhibited the gastric emptying of liquid in awake rats by causing an acid-base imbalance. In the present study, we investigated the involvement of the nitric oxide-cyclic guanosine monophosphate (NO-cGMP) pathway, vasoactive intestinal peptide (VIP), and corticotropin-releasing factor (CRF) peptide in this phenomenon.
Braz J Med Biol Res. Publicado em: 04/10/2018
-
5. Fatigue Strength and Fatigue Fracture Mechanism for Spot Welds in U-Shape Specimens
Abstract In this paper, the fatigue behavior of the metallic welded U-shape specimens subjected to cyclic loading have been investigated via experimental and numerical analysis. To do so, two sets of the spot welded specimens with different sizes were prepared and fatigue tests were conducted under the various cyclic loads. The crack propagation is numerical
Lat. Am. j. solids struct.. Publicado em: 2016-12
-
6. Effect of an Opening on Reinforced Concrete Hollow Beam Web Under Torsional, Flexural, and Cyclic Loadings
Abstract Hollow sections have been increasingly applied in the construction of buildings, bridges, offshore structures, and towers for passing electrical and mechanical pipes or other utilities. Torsion caused by external force is a weakness of hollow sections that is rarely investigated. In particular, the behavior of hollow sections with high-strength conc
Lat. Am. j. solids struct.. Publicado em: 2016-08
-
7. Biomechanical performance of Bio Cross-Pin and EndoButton for ACL reconstruction at femoral side: a porcine model
Abstract Introduction The method of graft fixation is critical in anterior cruciate ligament (ACL) reconstruction surgery. Success of surgery is totally dependent on the ability of the implant to secure the graft inside the bone tunnel until complete graft integration. The principle of EndoButton is based on the cortical suspension of the graft. The Cross-P
Res. Biomed. Eng.. Publicado em: 04/03/2016
-
8. Graft tendon slippage with metallic and bioabsorbable interference screws under cyclic load: a biomechanical study in a porcine model
Introduction The rupture of the anterior cruciate ligament (ACL) is the most common type of knee injury. Reconstructive surgery is the ‘gold standard’ treatment. During the immediate post-operative period, the fixation of the graft is entirely dependent on the ability of the grafted implant to be secured inside the bone tunnel under the cyclical loads a
Res. Biomed. Eng.. Publicado em: 2015-03
-
9. Surface contact fatigue failure of a case hardened pinion shaft
An investigation was made to determine the causes of surface contact fatigue failure of a case hardened driver pinion located in the intermediate shaft of a reducer gearbox used in a sugar and alcohol mill. The examination of the component revealed the presence of a cemented layer substantially thicker than that generally specified for pinions devised for th
Mat. Res.. Publicado em: 20/05/2014
-
10. Study of structural capacity and serviceability affecting the obstruction of residential door
The last Chilean earthquake, occurred on February 27, 2010, allowed establishing important patterns of structural failures in reinforced concrete residential buildings; however, limited progress has been made in the study of basic standards of serviceability, such as obstruction of doors. Thus, this study focused on measuring the influence of design specific
Lat. Am. j. solids struct.. Publicado em: 2014-05
-
11. Load-bearing capacity of screw-retained CAD/CAM-produced titanium implant frameworks (I-Bridge®2) before and after cyclic mechanical loading
Implant-supported screw-retained fixed dental prostheses (FDPs) produced by CAD/ CAM have been introduced in recent years for the rehabilitation of partial or total endentulous jaws. However, there is a lack of data about the long-term mechanical characteristics. OBJECTIVE: The aim of this study was to investigate the failure mode and the influence of exten
J. Appl. Oral Sci.. Publicado em: 2013-07
-
12. Fracture resistance of endodontically treated teeth restored with different intraradicular posts with different lengths
AIM: This study compared the resistance to fracture of endodontically treated teeth restored with different intraradicular posts with different lengths and full coverage metallic crowns. METHODS: Sixty extracted human canine teeth were randomly divided into 6 groups. Groups CP5, CP75 and CP10 were restored using custom cast post and core (CP) and groups PF5,
Braz. J. Oral Sci.. Publicado em: 2013-03