Cylinder
Mostrando 1-12 de 486 artigos, teses e dissertações.
-
1. Broadband Antennas Based on the Double Moebius Strip
Abstract The family of new antenna designs based on the double Moebius strip principle is proposed in this article. Three possible options of the power supply port location had been reviewed in this respect: the cut external strip with the signal port located directly in the cut area is used; the continuous rings without discontinuities are applied, with the
Journal of Microwaves, Optoelectronics and Electromagnetic Applications. Publicado em: 2022
-
2. Microstructure and diametral fracture strength of spark plasma sintered WC-6Co-0.2B and WC-6Co-0.5B ceramic composites from nanosized and metastable WC powders
Abstract The present work aimed at evaluating the microstructures and mechanical properties of spark plasma sintered WC-6 wt% Co ceramic composites doped with boron (0.2 and 0.5 wt%). W-50 at% C (W-6.13 wt% C) powders produced under different milling times (20, 60, 180, and 600 min) were used as starting materials and subsequently mixed with Co (6 wt%) and B
Cerâmica. Publicado em: 2022
-
3. Comparative vegetative anatomy of Neotropical Goodyerinae Klotzsch (Orchidaceae Juss.: Orchidoideae Lindl.)
ABSTRACT The Neotropical genera Aspidogyne and Microchilus (Goodyerinae, Cranichideae, Orchidaceae) comprise ca. 200 rainforests terrestrial species. Although species of Goodyerinae are described with similar anatomy to other taxa of Cranichideae, some anatomical characteristics appear to be specific to the subtribe. Our goal was to characterise the anatomic
Acta Bot. Bras.. Publicado em: 2020-09
-
4. DESIGN OF ELECTRONIC CONTROL GOVERNOR FOR A SINGLE CYLINDER GASOLINE ENGINE BASED ON AN INTELLIGENT SENSING ALGORITHM
ABSTRACT At present, most large machinery and vehicle engines are electronically controlled but their electronic control systems are too expensive to be popularised and applied in small gasoline engines with relatively low prices. Therefore, small gasoline engines still use mechanical speed regulators. Mechanical speed regulators not only have the defects of
Eng. Agríc.. Publicado em: 2020-08
-
5. 3D numerical investigation of mixture formation and combustion in a DISI engine at part-load under stratified operation
This work investigates through numerical simulation, the operation of a big bore direct fuel injection spark ignition engine, at part load under stratified operation. It evaluates fuel-air mixture preparation and combustion process with the adoption of detailed chemical kinetics mechanisms for both Isooctane and Ethanol, and applying adaptive mesh refinement
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 2020
-
6. Fracture strength of monocrystalline and polycrystalline ceramic brackets during archwire torque
Resumo Introdução A demanda por tratamentos estéticos tem crescido nos últimos anos, sendo cada vez mais forte a preocupação com a estética por parte dos pacientes que buscam o tratamento ortodôntico. Objetivo Este estudo avaliou a resistência à fratura de bráquetes cerâmicos monocristalinos e policristalinos de diferentes fabricantes quando su
Rev. odontol. UNESP. Publicado em: 03/10/2019
-
7. Tensile and fatigue properties, machinability and machined surface roughness of Al-Si-Cu alloys
ABSTRACT In this paper, the aim was to determine if ASC91 (9 % Al, 1 % Cu) could be replaced with ASC73 (7 % Al, 3 % Cu) aluminium alloy, with presumably improved machinability due to lower silicon content (9 to 7 %) and retained mechanical properties due to a higher copper content (1 to 3 %). The test samples were excised from cylinder heads produced by the
Matéria (Rio J.). Publicado em: 16/09/2019
-
8. Quantification and qualification of exhaust gases in agricultural diesel engine operating with biodiesel mixtures
RESUMO Motores de ciclo diesel são amplamente utilizados em máquinas agrícolas. O biodiesel oferece a possibilidade de substituição parcial ou total do diesel mineral, reduzindo assim a dependência da agricultura desse recurso não renovável e diminuindo as emissões de poluentes. O objetivo deste estudo foi avaliar as emissões de CO, NOx, SO2, CO2 e
Rev. bras. eng. agríc. ambient.. Publicado em: 09/09/2019
-
9. In-the-bag toric intraocular lens implantation in the case of an anterior capsule tear: a case series
RESUMO Objetivo: Analisar os resultados do implante de lentes intraoculares tóricas para rupturas capsulares anteriores durante a facoemulsificação. Métodos: A coorte desta série retrospectiva, consecutiva e intervencional de casos que inclui 8 pacientes. Um paciente foi excluído quando a lágrima foi usada para aumentar a rexe. O astigmatismo pré-o
Arq. Bras. Oftalmol.. Publicado em: 29/08/2019
-
10. Calibration of high-temperature furnace assemblies for experiments between 200 and 600 MPa with end-loaded piston-cylinder apparatuses
Abstract We present pressure calibration results for piston-cylinder –” and 1” high temperature furnace assemblies in the 200-600 MPa range aiming to expand its applicability to simulate upper crustal conditions. The furnace assemblies were made up by crushable MgO, graphite heater, pyrex glass spacer, and NaCl sleeve. Twenty-one experiments were carri
Braz. J. Geol.. Publicado em: 15/04/2019
-
11. Collaboration, competition and innovation: a consortium of tribology in the automotive sector
Abstract Paper aims The collaboration among competitors represents a substantial challenge for most innovation processes of companies. This research aims to explore the factors influencing collaboration for innovation that involves competitors in the Fuzzy Front End phase. Originality This study provides an important advance in three aspects. First, it b
Prod.. Publicado em: 15/04/2019
-
12. Influence of the Micromechanics Models and Volume Fraction Distribution on the Overall Behavior of SiC/Al Functionally Graded Pressurized Cylinders
Abstract The assessment of the differences in results obtained from various micromechanics homogenization schemes, as well as the implications of assuming different volume fraction profiles was carried out in the present work. The functionally graded composite chosen for the analysis was Al-SiC and comparisons were made in terms of stress and strain distribu
Lat. Am. j. solids struct.. Publicado em: 08/04/2019