Cylindrical Plunge Grinding
Mostrando 1-12 de 14 artigos, teses e dissertações.
-
1. Influence of water in the MQL technique in the grinding of steel AISI 4340 using CBN wheels
Abstract Usually, machining employs cooling methods to avoid high temperatures. In most cases, the cutting fluid is applied with high flow and low pressures. This technique consumes a large amount of cutting fluid that causes serious problems in the environment and in the health of the worker. An alternative to the conventional cooling method is the Minimum
REM, Int. Eng. J.. Publicado em: 2018-07
-
2. Evaluation of the oil flow using the MQL technique applied in the cylindrical plunge grinding of AISI 4340 steel with cbn grinding wheel
Abstract The grinding process is defined as an abrasive cutting action of a tool known as grinding wheel, which is submitted to high rotations, promoting excellent finishing and accuracy in dimensions, respecting the parameters established in each project. During the machining, the cutting edges of the abrasive grains undergo wearing and this increases the c
REM, Int. Eng. J.. Publicado em: 2018-07
-
3. Application viability evaluation of the Minimum Quantity Lubrication coolant technique under different flow rates in Plunge Cylindrical Grinding of the ABNT 4340 steel with aluminum oxide wheel
Abstract The coolant delivery technique known as Minimal Quantity Lubrication (MQL) has been employed in machining since the end of the 20th Century and has gained considerable evidence in the last years as a viable alternative to the use of the conventional coolant technique (flood). Due to the low oil flow rate delivered by the MQL technique in grinding op
REM, Int. Eng. J.. Publicado em: 2017-12
-
4. Surface Integrity Characterization of Hardened AISI 4340 Steel in Grinding Process with Biodegradable Formulations of Cutting Fluids
Surface integrity has significant effect on service performance of a component. The surface integrity of workpieces submitted to grinding process depends on the conditions of cooling produced by cutting fluids, which are used to avoid microstructural damage in the process. However, cutting fluids are harmful to the environment and human health, and appear as
Mat. Res.. Publicado em: 20/02/2017
-
5. Evaluation of different methods of cooling-lubrication in cylindrical grinding of advanced ceramic dip
The current work presents a study of alternative methods of cooling-lubrication for the external plunge grinding of advanced ceramics using diamond wheels. These two alternative methods, which are intended to reduce cutting fluid expenses, are commonly referred to as the optimized cooling-lubrication method and minimal quantity of lubrication (MQL). The tech
Mat. Res.. Publicado em: 30/09/2014
-
6. Behavior of surface integrity in cylindrical plunge grinding using different cooling systems
The superficial texture of the material can exert a decisive influence on the application and performance of the machined component. The conventional fluids used in grinding processes are environmental risk and can also be dangerous to the health. The disposal of these toxic fluids is expensive and the contamination in the proximities of the machines can pre
Materials Research. Publicado em: 15/04/2011
-
7. Influence of optimized lubrication-cooling and minimum quantity lubrication on the cutting forces, on the geometric quality of the surfaces and on the micro-structural integrity of hardened steel parts
The is paper presents an analysis of the influence of minimum quantity lubrication (MQL), optimized and conventional cooling, using different cutting fluid volumes and flow rates, on the surface quality and integrity of hardened steel workpieces, in cylindrical plunge grinding with superabrasive CBN grinding wheels. The final quality of the workpieces were e
Matéria (Rio de Janeiro). Publicado em: 2011
-
8. Comparing different plunge cylindrical grinding cycles based on workpiece roughness and process vibration
Grinding is an important process used when tight dimensional accuracy and low workpiece surface roughness are demanded. Despite the fact that grinding is widely used in industry, it is not well understood. The elastic deformation, which occurs in the beginning of the cycles, makes it necessary a spark out in the end of the cycle. An alternative to this is th
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2009-06
-
9. Analysis of the influence of sparkout time on grinding using several lubrication/cooling methods
The plunge cylindrical grinding operation has been widely employed in the manufacturing process of components which require excellent surface quality achieved within small ranges of dimensional tolerance. The sparkout time has proved to be an important parameter in this operation, contributing to obtain surfaces with high geometric and dimensional precision.
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2009-03
-
10. Application of the Minimum Quantity Lubrication (MQL) technique in the plunge cylindrical grinding operation
Precision cylindrical grinding is used extensively in the manufacture of precision components in the metal-mechanical industry in general. Modern CNC grinding machines have improved this process with respect to the positioning and rigidity of the machine-workpiece-tool system, allowing the production of high precision parts with low dimensional tolerances. B
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2009-03
-
11. Método prático para otimização do ciclo de retificação transversal de precisão / Practical way to optimization the cycle of precision plunge grinding
Este trabalho descreve uma forma prática para planejamento do ciclo de operação de retificação por mergulho, em função da especificação dimensional da peça e da rigidez da máquina. Essa otimização é estendida além do ciclo, envolve produzir lotes de peças com dispersão das dimensões dentro de limites especificados. O tempo de set-up, que no
Publicado em: 2009
-
12. Uma contribuição a otimização do processo de retificação cilindrica de mergulho do aço SAE 4340
The goal of work goal is study the influence of grinding parameters, feed velocities, stock remova! and time of cycle, in the surface quality of the workpiece (surface roughness and roundness measurement), as well as the deformation leveI imposed to the system machineworkpiece-tool. This study was accomplished for both the grinding cycle with 3 phases (cycle
Publicado em: 2004