Dynamic Scanning Calorimetry
Mostrando 1-12 de 73 artigos, teses e dissertações.
-
1. ERRATUM
This study described the morphology, crystallinity, thermal and mechanical characterization of Polyamide 11 (PA11) porous film prepared by non-solvent induced phase separation (NIPS) method using formic acid (FA) as solvent. In addition, the miscibility of PA11/FA/H2O system was performed to generate a ternary phase diagram. The porous films morphology was i
Arq. Neuro-Psiquiatr.. Publicado em: 2021-06
-
2. Polyamide 11 porous films by NIPS: the influence of miscibility and polymer crystalline formation in pores structure and morphology
This study described the morphology, crystallinity, thermal and mechanical characterization of Polyamide 11 (PA11) porous film prepared by non-solvent induced phase separation (NIPS) method using formic acid (FA) as solvent. In addition, the miscibility of PA11/FA/H2O system was performed to generate a ternary phase diagram. The porous films morphology was i
Quím. Nova. Publicado em: 2021-06
-
3. Heterotopic Heart Transplant History and Concepts Cannot Be Neglected - Witnessing the History and Learning with Previous Practices
This study described the morphology, crystallinity, thermal and mechanical characterization of Polyamide 11 (PA11) porous film prepared by non-solvent induced phase separation (NIPS) method using formic acid (FA) as solvent. In addition, the miscibility of PA11/FA/H2O system was performed to generate a ternary phase diagram. The porous films morphology was i
Braz. J. Cardiovasc. Surg.. Publicado em: 2021-06
-
4. Sustainable blends of LDPE/NR and sugarcane bagasse ashes with PE-g-MA thermomechanical relationships
RESUMO As blendas poliméricas obtidas com resíduos que antes eram chamados de lixos vêm crescendo como uma solução viável, permitindo melhorias nas propriedades mecânicas e como alternativas sustentáveis. Este trabalho relata os efeitos de misturas de polietileno de baixa densidade (PEBD) e borracha natural(NR), com cinzas de bagaço de cana-de-açú
Matéria (Rio J.). Publicado em: 16/09/2019
-
5. Comportamento térmico de compósitos de poliestireno reciclado reforçado com celulose de bagaço de cana
RESUMO O poliestireno expandido (EPS) é um polímero reciclável amplamente utilizado na fabricação de embalagens para isolamento acústico, proteção de bens de consumo duráveis e na indústria da construção civil. O PS é facilmente reciclável com o aumento da temperatura, podendo dar origem a novos materiais. Entretanto suas propriedades térmicas
Matéria (Rio J.). Publicado em: 16/09/2019
-
6. Thermomechanical Properties of Corn Starch Based Film Reinforced with Coffee Ground Waste as Renewable Resource
Abstract Starches polymeric films offer several advantages for the replacement of synthetic polymers due to their biodegradability, non-toxicity, availability and low cost. However, the high biodegradation potential can cause fragility, considering some fundamental mechanical properties. Therefore, starch based polymeric films were reinforced incorporating l
Mat. Res.. Publicado em: 07/01/2019
-
7. Changes in the crystalline degree in neutron irradiated EPDM viewed through infrared spectroscopy and inelastic neutron scattering
ABSTRACT The changes in the degree of crystallinity in commercial Ethylene Propylene Diene rubber-type M (EPDM) irradiated with neutrons at different doses has been studied by means of inelastic neutron scattering and infrared absorption spectroscopy experiments. EPDM samples were taken from the housing of non-ceramic electrical insulators which are used in
Matéria (Rio J.). Publicado em: 19/07/2018
-
8. Estabilidad de las fases U3Si5, USi2-x y USi2 al incorporar Al en solución. Experiencias de calorimetría diferencial de barrido
ABSTRACT U(Mo) alloys are being studied to be applied as a fuel for research and test reactors. When U(Mo) particles are dispersed in an Al matrix, it is known that an interdiffusion during fabrication process and / or irradiation. In this sense, irradiation tests have shown that this IL has a bad behavior under irradiation coming up the addition of Si to Al
Matéria (Rio J.). Publicado em: 19/07/2018
-
9. Evaluation of Out-of-Autoclave (OOA) epoxy system
Abstract Epoxy resins (EP) usually cure in autoclave to minimize resin voids and to achieve the desired resin/fiber ratio. Cure parameters such as temperature, vacuum and pressure levels are controlled and monitored. Aiming time and cost optimization, new out-of-autoclave (OOA) cure processes have been developed lately. This study evaluated the cure cycle an
Polímeros. Publicado em: 2017-12
-
10. A Microrheological Study of Poly(Methyl Methacrylate) Elastomer/Poly(Ethylene Terephthalate) (PMMAelast/PET) Blends
This study involved an evaluation of the influence of phase inversion in poly(methyl methacrylate) elastomer/poly(ethylene terephthalate) binary blends (PMMAelast/PET) and the effect of the addition of poly(methyl methacrylate-glycidyl methacrylate-ethyl acrylate) (MGE) interfacial compatibilizer on the microrheological properties of this polymer blend. Ther
Mat. Res.. Publicado em: 30/11/2017
-
11. Thermal and mechanical properties of bio-based plasticizers mixtures on poly (vinyl chloride)
Abstract The use of mixtures of nontoxic and biodegradable plasticizers coming from natural resources is a good way to replace conventional phthalates plasticizers. In this study, two secondary plasticizers of epoxidized sunflower oil (ESO) and epoxidized sunflower oil methyl ester (ESOME) were synthesized and have been used with two commercially available b
Polímeros. Publicado em: 21/09/2017
-
12. Differential Scanning Calorimetry study on curing kinetics of diglycidyl ether of bisphenol A with amine curing agents for self-healing systems
ABSTRACT Epoxy resin is one of the most important polymeric matrixes for diverse uses, such as aeronautical, mobile, electronics and others. Providing a material capable of self-healing microcracks will allow it to have a more reliable and longer use. In order to study this new property of self-healing to an epoxy resin, a Differential Scanning Calorimetry (
Matéria (Rio J.). Publicado em: 20/07/2017