Electrical Heating
Mostrando 1-12 de 60 artigos, teses e dissertações.
-
1. HYBRID SYSTEM SIMULATION TO SUPPLY HEATED AIR TO A SOLAR FOOD DRYER
ABSTRACT The intermittence of solar radiation, due to continuous rainy or cloudy days, is a limitation of simple and small solar dryers. These conditions often make them impossible to use. By including storage systems (thermal accumulation) and/or auxiliary energy sources, drying processes or dehydration can be conducted continuously, even during periods of
Eng. Agríc.. Publicado em: 2020-04
-
2. The Surface Treatment of Niobium Superconducting Reentrant Cavities by Means of High Temperature Nitrogen Plasma Based Ion Implantation
High Temperature Nitrogen Plasma Based Ion Implantation (HT-NPBII) has been used to treat the surface of niobium superconducting reentrant cavities, which are part of parametric transducers in a resonant-mass gravitational wave detector. The aim is to enhance the corresponding electrical quality factors (Q-factors) which are closely related with the increase
Mat. Res.. Publicado em: 13/12/2019
-
3. HYBRID SOLAR HEAT PUMP SYSTEM FOR WATER HEATING
ABSTRACT A comparative test of water heating between the hybrid system - solar collector with heat pump - and a system with conventional supplementary heating - with high electric power - was performed. For this, a small capacity heat pump was installed, which was later installed together with a solar heating system, composed of a 250 L thermal reservoir and
Eng. Agríc.. Publicado em: 12/08/2019
-
4. Estimativa do potencial de recuperação energética de resíduos sólidos urbanos usando modelos matemáticos de biodigestão anaeróbia e incineração
RESUMO Atualmente, um dos grandes problemas enfrentados pelos gestores de resíduos sólidos urbanos (RSU) é a disposição final dos resíduos gerados por sua população. As disposições de resíduos devem ser feitas em espaços e sob condições adequados de modo a minimizar os impactos socioeconômicos e ambientais. Nesse contexto, este artigo teve por
Eng. Sanit. Ambient.. Publicado em: 30/05/2019
-
5. Temperature Dependence of Electrical Resistance in Ge-Sb-Te Thin Films
Nowadays, the Ge-Sb-Te system is studied extensively for use in the field of both electrical and optical non-volatile memories. The key of this application is based on the changes in the physical properties (electrical conductivity or refractive index) of these films as a result of structural transformation between amorphous and crystalline states. Both stat
Mat. Res.. Publicado em: 18/02/2019
-
6. Controller for a SPS machine: a proposal PI control
ABSTRACT Temperature control is the key to effective sintering process for metal, ceramic and polymer powders. The original control temperature provides an irregular control operation process which affects the material properties due to the spacer involved in it. Furthermore, it is analyzed how the material responds to an electrical input determining a model
Matéria (Rio J.). Publicado em: 19/07/2018
-
7. Método innovador de ensayos de impacto en altas temperaturas aplicado en aceros al carbono
ABSTRACT In this paper, an innovative method of impact tests at high temperature on sub-size Charpy V notched specimens is applied. The innovation lies in the method of heating the specimen, which is performed in situ on a Charpy impact machine type by alternating electrical current through the specimen. The specimens are heated in a few seconds (v=32 ºC/s)
Matéria (Rio J.). Publicado em: 19/07/2018
-
8. Electrical Conductivity in the KDP, ADP, and K1-x(NH4)xH2PO4 Crystals
Impedance Spectroscopy was performed to examine the electrical conductivity on KH2PO4 KDP, (NH4)H2PO4 ADP and K1-x(NH4)xH2PO4 (x = 0.076, 0.118, 0.357, 0.857, 0.942) crystals with increasing temperature. They were grown by solvent evaporation method. Zview simulation software was used to theoretically fit electrical conductivity results as a function of freq
Mat. Res.. Publicado em: 23/02/2017
-
9. Experimental dryer design for agricultural products
ABSTRACT This study consisted of designing and building an experimental dryer that allows working with different temperatures and velocities of the air, aiming to perform studies on thin- and thick-layer drying of agricultural products. The project was divided into three stages: heat source designing, dryer geometric parameters, and fan selection to meet ope
Eng. Agríc.. Publicado em: 2016-10
-
10. Effect of Spun Velocities and Composition on the R‒phase and Thermomechanical Behavior in Ti‒Ni Ribbons Electrically Heated
This work deals with structural, electrical and mechanical characterization of Ti‒50.13Ni and Ti‒49.62Ni (at.%) shape memory alloys (SMAs) fabricated at different circumferential wheel velocities. The effect of wheel velocity, chemical composition and heat treatments are investigated. The characterization of crystallographic phases of the Ti‒Ni ribbons
Mat. Res.. Publicado em: 08/04/2016
-
11. Determination of Microstructure, Mechanical, Electrical and Thermal Properties of The Directionally Solidified Al-Si-Co Ternary Alloy
In this work, Al-12.6Si-2Co (wt.%) ternary alloy of near eutectic composition was directionally solidified at a constant temperature gradient (G=7.60 K/mm) in a wide range of growth rates (V=8.35-166.30 µm/s) using by Bridgman type growth apparatus. Flake spacing (λ), microhardness (HV), tensile stress (σ) and electrical resistivity (ρ) were measured fro
Mat. Res.. Publicado em: 26/02/2016
-
12. Study of aluminum nitride precipitation in Fe- 3%Si steel
For good performance of electrical steels it is necessary a high magnetic induction and a low power loss when submitted to cyclic magnetization. A fine dispersion of precipitates is a key requirement in the manufacturing process of Fe- 3%Si grain oriented electrical steel. In the production of high permeability grain oriented steel precipitate particles of c
Mat. Res.. Publicado em: 11/06/2013