Electrical Simulation
Mostrando 1-12 de 135 artigos, teses e dissertações.
-
1. Optimization Techniques and Mathematical Modeling Applied to Reluctance Motors
Abstract The present work aims at the application of different optimization strategies in the electromagnetic analysis of the Variable Reluctance Motor (VRM) through Finite Element (FE) simulation. Two case studies are investigated: the first one aims to optimize the geometry and electrical characteristics of windings of a single-phase VRM 6/6, minimizing co
Journal of Microwaves, Optoelectronics and Electromagnetic Applications. Publicado em: 2022
-
2. HYBRID SYSTEM SIMULATION TO SUPPLY HEATED AIR TO A SOLAR FOOD DRYER
ABSTRACT The intermittence of solar radiation, due to continuous rainy or cloudy days, is a limitation of simple and small solar dryers. These conditions often make them impossible to use. By including storage systems (thermal accumulation) and/or auxiliary energy sources, drying processes or dehydration can be conducted continuously, even during periods of
Eng. Agríc.. Publicado em: 2020-04
-
3. Estimativa do potencial de recuperação energética de resíduos sólidos urbanos usando modelos matemáticos de biodigestão anaeróbia e incineração
RESUMO Atualmente, um dos grandes problemas enfrentados pelos gestores de resíduos sólidos urbanos (RSU) é a disposição final dos resíduos gerados por sua população. As disposições de resíduos devem ser feitas em espaços e sob condições adequados de modo a minimizar os impactos socioeconômicos e ambientais. Nesse contexto, este artigo teve por
Eng. Sanit. Ambient.. Publicado em: 30/05/2019
-
4. Contrastive Research on Electrical Contact Performance for Contact Materials of Cu-SnO2 and Cu-ZnO2 Alloys
Herein, SnO2- and ZnO2-doped (1.5 wt.%) composite Cu powder was prepared by mechanical alloying (MA) respectively, and both the contact materials of oxide-doped Cu alloys were subsequently obtained by canned hot-pressing powder sintering with hot extrusion combined. Scanning electron microscopy (SEM), laser scanning confocal microscopy (LSCM) and self-design
Mat. Res.. Publicado em: 25/04/2019
-
5. Generation of Electrical Energy Obtained Through a Continuous Current Generator Coupled to the Pedal of an Ergometric Bicycle
ABSTRACT This study presents a system of conversion of mechanical energy produced by physical activity into electric energy obtained by a CC generator coupled to the pedal of an ergometric bicycle. It presents the converter that will be used to adjust the voltage and power coming from the system, as well as the details of the converter design, the simulation
Braz. arch. biol. technol.. Publicado em: 29/11/2018
-
6. Computational Model for Microgeneration Simulation, From Solar and Wind Renewable Sources, With Optimal Allocation of Loads, Electric Vehicle and Energy Storage, In a Residential Electrical Micro Network
Abstract The electrical sector is under constant evolution. One of the areas refers to the consumers that come to be generators, implementing distributed generation, interconnected to a smart grid. This article discusses the improvement of an algorithm, already presented in the literature, to make the best temporal allocation of loads, electric vehicle, stor
Braz. arch. biol. technol.. Publicado em: 29/10/2018
-
7. Mathematical Modeling And Numerical Simulation of Dropwise Condensation on an Inclined Circular Tube
ABSTRACT: Dropwise condensation can improve heat transfer process and, consequently, leads to considerable reduction in size and weight of condensers as well as improvement in the dehumidification process in many applications, especially in civil transport aircraft. It can also be used as an efficient cooling tool for electronics and electrical systems in ai
J. Aerosp. Technol. Manag.. Publicado em: 2017-12
-
8. Theoretical study of c-GaN/GaAs single heterojunction solar cells
ABSTRACT In this work a theoretical study of electrical behavior for a c-GaN/GaAs heterostructure as a photovoltaic device through a two-dimensional (2D) finite element numerical simulation is presented for a first time. I-V curves and electrical parameters like short circuit current (Isc), open circuit voltage (Voc), fill factor (FF) and efficiency (η) wer
Matéria (Rio J.). Publicado em: 02/10/2017
-
9. Assessment of Percolation Threshold Simulation for Individual and Hybrid Nanocomposites of Carbon Nanotubes and Carbon Black
Modeling electrical conductivity of polymer composites with conductive fillers has great applicability to predict conductive materials behavior. In this study, the electrical behavior of simple and hybrid systems prepared from Carbon Black (CB) and Carbon Nanotubes (CNT) was studied. There have been few advances reported in the literature regarding the model
Mat. Res.. Publicado em: 18/09/2017
-
10. Electrical Conductivity in the KDP, ADP, and K1-x(NH4)xH2PO4 Crystals
Impedance Spectroscopy was performed to examine the electrical conductivity on KH2PO4 KDP, (NH4)H2PO4 ADP and K1-x(NH4)xH2PO4 (x = 0.076, 0.118, 0.357, 0.857, 0.942) crystals with increasing temperature. They were grown by solvent evaporation method. Zview simulation software was used to theoretically fit electrical conductivity results as a function of freq
Mat. Res.. Publicado em: 23/02/2017
-
11. Combined Cycle Performance Evaluation and Dynamic Response Simulation
ABSTRACT Power plants operating in combined cycle present higher thermal efficiency (over 60%) and increased power generation when compared to traditional simple cycles, such as gas or steam turbines operating alone. Considering that the power plant evaluated in this paper is already operational, a further development concerning to the power plant control sy
J. Aerosp. Technol. Manag.. Publicado em: 2016-12
-
12. A Study on Formation Process of Secondary Upsetting Defect in Electric Upsetting and Optimization of Processing Parameters Based on Multi-Field Coupling FEM
The electric upsetting process is an excellent electrically assisted preforming technique with electrical-thermal-mechanical multi-field coupling characteristic. The secondary upsetting defect in electric upsetting with inappropriate parameters combinations could result in folds in subsequent forging process. In order to analyze the formation process of the
Mat. Res.. Publicado em: 04/07/2016