Electrical Steels
Mostrando 1-12 de 26 artigos, teses e dissertações.
-
1. Improvement of Texture and Magnetic Properties in 4.5 wt.% Si Grain-Oriented Electrical Steels
4.5 wt.% Si grain-oriented electrical steel sheets were successfully produced by hot rolling, normalizing, warm rolling and annealing, and texture evolution was investigated using macro- and micro-texture analysis. It is found that the recrystallization texture of sheets is very sensitive to the warm rolling reduction, and 83-87% warm rolling reductions are
Mat. Res.. Publicado em: 19/08/2019
-
2. Influência do Regime Transiente Sobre a Microdureza e Microestrutura nos Aços ASTM-A36 e SAE-1045 Soldados pelo Processo MAG
Resumo O regime quase-estacionário pode não ser alcançado em soldagens a arco elétrico de peças de pequenas dimensões e/ou de materiais de maior condutividade térmica. Entretanto, o regime transiente sempre ocorrerá no início e no final da soldagem. Neste regime, a variação do fluxo de energia via calor pode promover variações microestruturais e
Soldag. insp.. Publicado em: 08/08/2019
-
3. Método innovador de ensayos de impacto en altas temperaturas aplicado en aceros al carbono
ABSTRACT In this paper, an innovative method of impact tests at high temperature on sub-size Charpy V notched specimens is applied. The innovation lies in the method of heating the specimen, which is performed in situ on a Charpy impact machine type by alternating electrical current through the specimen. The specimens are heated in a few seconds (v=32 ºC/s)
Matéria (Rio J.). Publicado em: 19/07/2018
-
4. Evaluación del Deterioro de los Electrodos al Incrementar el Número de Pulsos del Tiempo de Soldadura en Aceros IF y HSLA Galvanizados y la Afectación de las Propiedades Mecánicas en los Puntos de Soldadura
Abstract: Resistance welding points, is the most important method in the assembly industry of unibody because of its automation, which is defined as the ability of the structure to provide adequate protection to passengers against injury from a collision, mainly depends on the mechanical performance of the weld nugget. To extend the life of vehicles produced
Soldag. insp.. Publicado em: 05/01/2017
-
5. Effect of Cross-Rolling on Microstructure, Texture and Magnetic Properties of Non-Oriented Electrical Steels
Hot rolled non-oriented electrical steel samples were subjected to cold cross-rolling of 80 % reduction in thickness. The cross-rolled samples were then annealed at 650, 750 and 850 ºC for 1 hr, 2 hrs and 4 hrs respectively. The role of cross-rolling on microstructure, texture and magnetic properties of the samples after annealing has been investigated. Two
Mat. Res.. Publicado em: 16/12/2016
-
6. Effect of Aluminium Addition on the Magnetic Properties of a Semi-Processed Electrical Steel
Aluminum is often added to electrical steels since this element causes improvement of the magnetic properties. However the addition of aluminum is usually limited to 0.30 wt%1. Therefore, this work aimed at evaluating the influence of higher levels of aluminum in the magnetic properties of semi-processed steels. To accomplish this, four types of steel were p
Mat. Res.. Publicado em: 12/09/2016
-
7. Anomalous loss hysteresis loop
This paper discusses the anomalous loss behavior in two electrical steels types. Starting from a non oriented electrical steel coil, three groups of samples with different grain sizes were produced. Grain oriented steel samples were produced from a commercially available material. The experimental procedure was performed by means of magnetic properties measu
Mat. Res.. Publicado em: 28/02/2014
-
8. Case depth in SAE 1020 steel using barkhausen noise
The most widely used thermochemical process for surface hardening of steels is case hardening. Using several different heat treatments, martensitic surface layers were formed on SAE 1020 steel into which carbon had been diffused. Case depths were measured by traditional destructive techniques. Barkhausen noise measurements were made and both the RMS Barkhaus
Mat. Res.. Publicado em: 18/06/2013
-
9. Study of aluminum nitride precipitation in Fe- 3%Si steel
For good performance of electrical steels it is necessary a high magnetic induction and a low power loss when submitted to cyclic magnetization. A fine dispersion of precipitates is a key requirement in the manufacturing process of Fe- 3%Si grain oriented electrical steel. In the production of high permeability grain oriented steel precipitate particles of c
Mat. Res.. Publicado em: 11/06/2013
-
10. Estudo do comportamento termomecânico e análise da formação de orientações preferenciais de aços com 6,5% Si conformados por spray / Thermomechanical behavior and texture analysis in Spray formed 6.5% si-carbon steels
Termomechanical behavior of spray formed 6.5% Si-Carbon steels were analyzed by physical simulation, through torsion tests, and the evolution of preferential orientation were analyzed in order to electrical devices. Low carbon steel was used in spray forming, and the parameters were changed in order to minimize porosity. The carbon content in Specimens influ
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 29/07/2012
-
11. Testing strategies to evaluate non-oriented electrical steels losses
This paper presents an experimental comparative study of iron losses obtained by means of the Epstein frame, Ring Core and dynamometer tests with non-oriented electrical steel samples. The comparisons are qualitative and they are intended to show the importance of carrying out other tests to evaluate electrical steels in addition to the standard Epstein fram
J. Microw. Optoelectron. Electromagn. Appl.. Publicado em: 2012-12
-
12. A influência do recozimento descarbonetante nas propriedades magnéticas de aços para fins elétricos. / The influence of decarburizing annealing on magnetic properties of electrical steels.
Este trabalho analisa o efeito da descarbonetação nas perdas magnéticas de aços elétricos semiprocessados, após recozimento final, descarbonetante e/ou não-descarbonetante. Neste trabalho foi utilizado um aço de baixo carbono (600ppm de C) encruado a 4-6% de deformação, tipo COSCORE 55O. Foi notado que o recozimento descarbonetante reduz rapidament
Publicado em: 2011