Film Thickness
Mostrando 1-12 de 218 artigos, teses e dissertações.
-
1. Morphology Behavior of Copper Films Deposited after Wet Surface Treatment on Polished Alumina
In this paper, a pre-treatment process for electroless copper (Cu) deposition on the polished alumina (Al2O3) 99.9% and the behavior of Cu plating by electroless process after Al2O3 surface treatment were explored. Our work was carried out by changing the roughness of Al2O3 through micro-etching (coarsening), nucleation its surface by a two-step method (sens
Journal of the Brazilian Chemical Society. Publicado em: 2022
-
2. Application of self-organizing maps to evaluate the influence and behavior of the film formed during salting of Prato cheese
Abstract Problems related to high blood pressure have led consumers to choose foods with low levels of sodium chloride, and an alternative to reduce the salt content of this salt is its partial replacement with KCl. In order to not affect the sensory properties of cheese, salting was performed using a solution containing 70% of NaCl and 30% of KCl in a stati
Food Sci. Technol. Publicado em: 2020-12
-
3. Effect of Growth Parameters on the Photocatalytic Performance of TiO2 Films Prepared by MOCVD
The present study evaluated the main factors that influence the photocatalytic activity of titanium dioxide (TiO2) films grown by metalorganic chemical vapor deposition (MOCVD) at 400 and 500 °C, in different growth times. The photocatalytic behavior was analyzed by measuring the methyl orange dye degradation at different pH values. Structural and morpholog
J. Braz. Chem. Soc.. Publicado em: 2020-06
-
4. ANALYTICAL EXPRESSIONS FOR THE CONCENTRATION AND CURRENT IN THE REDUCTION OF HYDROGEN PEROXIDE AT A METAL-DISPERSED CONDUCTING POLYMER FILM
A mathematical model describing the reduction of Hydrogen peroxide (H2O2) to water in a metal dispersed conducting polymer film is discussed. The model is based on a system of reaction-diffusion equations containing a non-linear term related to Michaelis-Menten kinetics of the enzymatic reaction. The approximate analytical expressions corresponding to the co
Quím. Nova. Publicado em: 2020-01
-
5. Avaliação tribológica de óleos hidráulicos biodegradável e mineral com deslizamento entre as ligas de Cu-Zn e WC-CoCr
RESUMO A correta seleção dos óleos lubrificantes e das superfícies de contato melhoram o desempenho e reduzem o consumo de energia das máquinas Por isso, a engenharia de superfícies propõe novos revestimentos aos quais seu comportamento tribológico combinado com o uso de óleos biodegradáveis em componentes de sistema hidráulicos, não são conheci
Matéria (Rio J.). Publicado em: 25/11/2019
-
6. Mecanismos de queda do fluxo em membranas de microfiltração de poliéterimida aplicadas à clarificação de água produzida sintética
RESUMO Membranas de microfiltração de poliéterimida foram preparadas pelo método de inversão de fases para controlar a espessura, porosidade e tamanho de poros dos filmes. 1-metil-2-pirrolidona foi utilizada como solvente e água como não solvente. As propriedades das membranas foram avaliadas por meio de microscopia eletrônica de varredura, microfilt
Matéria (Rio J.). Publicado em: 25/11/2019
-
7. Influence of Pre-Heating Regular Resin Composites and Flowable Composites on Luting Ceramic Veneers with Different Thicknesses
Resumo O objetivo neste estudo foi avaliar a influência do pré-aquecimento, conteúdo de carga e espessura da cerâmica na espessura da película, resistência de união ao microcisalhamento, grau de conversão e alteração de cor na cimentação de cerâmicas. Dois compósitos experimentais foram preparados (Bis-GMA / UDMA / BisEMA / TEGDMA), com diferen
Braz. Dent. J.. Publicado em: 07/10/2019
-
8. The influence of Cu content on high temperature corrosion behavior of heat - resistant molten salt steel
ABSTRACT This work studies the high temperature corrosion behavior of new heat-resistant steel with salt coating method of 75%Na2SO4+25%NaCl coating on the steel surface at 700ºC. The chemical composition of corrosion products and surface morphology of the corrosion layer were analyzed using X-ray diffractometer (XRD), scanning electron microscopy (SEM), en
Matéria (Rio J.). Publicado em: 16/09/2019
-
9. Experimental-numerical Technique to Evaluate the Thickness of TiN Thin Film
In this study, the numerical analysis of instrumented indentation testing was combined with the experimental procedure to evaluate the mechanical properties and thickness of a titanium nitride (TiN) film deposited on titanium substrate (Ti) by plasma processing. TiN film thickness is an important parameter for the surface treatment industry. In numerical ana
Mat. Res.. Publicado em: 09/09/2019
-
10. Effect of Warm Rolling on the Corrosion and Mechanical Properties of UNS S32205 Duplex Stainless Steel
Duplex stainless steel (DSS) has been considered as an excellent alternative for applications where high corrosion resistance and high mechanical strength are required. Therefore, microstructure and properties of DSS remain topics of much interest. For this purpose, the effect of warm-rolling was studied in a duplex stainless steel. The focus of this work wa
Mat. Res.. Publicado em: 02/09/2019
-
11. Microtensile bond strength of root canal dentin treated with adhesive and fiber-reinforced post systems
Abstract Nowadays, demand for esthetic restorations has risen considerably; thus, nonmetal esthetic posts made of either high-strength ceramics or reinforced resins, such as fiber-reinforced resin posts, have become more and more popular. Important characteristics of fiber-reinforced posts involve a modulus of elasticity similar to dentin and their ability t
Braz. oral res.. Publicado em: 01/07/2019
-
12. Influência da densidade de potência e da porcentagem de N2 na atmosfera de deposição na dureza e no módulo de Young em filmes de aço inoxidável AISI 316 depositados por pulverização catódica
RESUMO O processo de recobrimento por pulverização catódica é uma técnica amplamente utilizada para produção de revestimentos metálicos e cerâmicos, devido a versatilidade no controle das propriedades com pequenas mudanças nos parâmetros de processo, como densidade de potência aplica ao cátodo magnetron e atmosfera de trabalho. Sendo assim, as p
Matéria (Rio J.). Publicado em: 20/05/2019