Fine Particles
Mostrando 1-12 de 214 artigos, teses e dissertações.
-
1. Evaluation of the Properties of LaNiO3 Material Prepared by the Modified Proteic Method for Adsorption of Environmental Contaminants
LaNiO3 material was synthesized by modified proteic method, calcined at 900 °C/2 h in air atmosphere and was applied to remove environmental contaminants. LaNiO3 phase with a perovskite structure was formed in the calcined material, which has a surface area of 22 m2 g-1 and is formed by fine particles agglomerated, with pH of the zero charge point of 7.44.
Journal of the Brazilian Chemical Society. Publicado em: 2023
-
2. The BigFLUX Magnetic Matrix Technology
Abstract The Magnetic separation of ultra-fine ore particles has always posed a challenge to the JONES/WHIMS process. Despite many advances in this technology, no effective improvement has been made to its core component: The Magnetic Matrix. The current approach to separate ultra-fine particles teaches that the gap of the matrix and its teeth size must be s
REM - International Engineering Journal. Publicado em: 2022
-
3. Interrill erodibility of different sandy soils increases along a catena in the Caiuá Sandstone Formation
ABSTRACT Soil erosion in tropical areas is a major problem for sustainability in agriculture and soil stability. In the Northwest of Paraná, cassava crop is produced using a conventional tillage system along a catena consisting of different soil classes: Ferralsols (near the summit), Lixisols (mid-slope), and Arenosols (foot-slope). Therefore, differential
Rev. Bras. Ciênc. Solo. Publicado em: 17/01/2020
-
4. Water retention capacity in Arenosols and Ferralsols in a semiarid area in the state of Bahia, Brazil
Abstract: One of the most serious problems in areas indicated for irrigation projects in the Brazilian Northeast region is the occurrence of sandy soils, known to have low moisture retention, but occurring in strategic locations in terms of water supply and geographical situation, and which can be used for agricultural purposes. The objective of this study
An. Acad. Bras. Ciênc.. Publicado em: 25/11/2019
-
5. Plastics floatability: effect of saponin and sodium lignosulfonate as wetting agents
Abstract Froth flotation is the most common process in mineral processing. For the separation of plastic mixtures by flotation, the use of appropriate wetting agents is mandatory. The floatability of six post-consumer plastics was studied at different concentrations of the wetting agents, saponin and sodium lignosulfonate. Also, the influence of size and sha
Polímeros. Publicado em: 03/10/2019
-
6. Statistical analysis of mechanical properties of mortars with fly ash and waste tire rubber
Resumo Este artigo tem como objetivo efetuar a análise estatística dos efeitos da inclusão da borracha de pneus inservíveis e cinza volante oriunda de usinas termelétricas como componentes da argamassa para revestimento de edificações. Foram produzidas argamassas de referência e argamassas contendo borracha com dimensão máxima dos grãos de 0,71 mm
Rev. IBRACON Estrut. Mater.. Publicado em: 23/09/2019
-
7. A study of packing parameters that influence the fresh properties of self-compacting concrete
Resumo Alguns métodos de dosagem de concreto autoadensável (CAA) conhecidos são baseados no menor índice de vazios como uma proposta de empacotamento ideal. Contudo, uma composição com um menor teor de vazios não é garantia de uma boa sinergia entre os grãos maiores e menores no estado fresco. O objetivo deste estudo foi identificar e avaliar difere
Cerâmica. Publicado em: 15/08/2019
-
8. Evaluation of the pozzolanic activity of red ceramic waste using mechanical and physicochemical methods
Resumo Materiais cimentícios alternativos podem reduzir potencialmente o impacto ambiental da extração de cal e a produção de cimento Portland. Resíduos de cerâmica vermelha podem ser triturados em partículas finas e usados como fíler ou adição pozolânica em argamassas de cimento Portland e cal. Este estudo apresenta a avaliação da atividade po
Cerâmica. Publicado em: 15/08/2019
-
9. Interações ambientais e resistência física de um depósito de resíduos finos da indústria de rochas ornamentais
RESUMO Embora vários trabalhos proponham aplicações para os resíduos finos gerados no beneficiamento de rochas ornamentais, ainda não há evidências das vantagens financeiras para tal aproveitamento. Assim, a descrição dos depósitos existentes, muitos deles construídos sem triagem ou qualquer medida de proteção ambiental, torna-se imprescindível
Eng. Sanit. Ambient.. Publicado em: 15/08/2019
-
10. Recovery of pellet feed from tailings dams
Abstract Not long ago, certain iron ore processing plants in Brazil were unable to efficiently recover iron ore fines and, as a result, operated only with high grade iron ore. For this reason, material stored in some iron ore tailings dams have considerable amounts of iron content with a potential to produce pellet feed fines through a concentration process.
REM, Int. Eng. J.. Publicado em: 19/06/2019
-
11. Effect of Extrusion and Heat Treatment on Microstructure and Mechanical Properties of Hypereutectic A390-0.3wt%Nd Alloy
An hypereutectic aluminium alloy with a composition of 16-18wt%Si, 4-5wt%Cu, 0.45-0.65wt%Mg, 0.3wt%Nd and Al balance (A390-0.3wt%Nd alloy) was processed by extrusion and aging at 200ºC for 10 hours. The effect of the thermomechanical processing and heat treatment on microstructure and mechanical properties was investigated for A390-0.3wt%Nd alloy. It was sh
Mat. Res.. Publicado em: 10/06/2019
-
12. Efeitos do uso de areia de praia nas propriedades de argamassas mistas: análise da variação granulométrica
RESUMO Devido ao alto consumo de areia de rio na construção civil e sua extração abusiva, cujos resultados são a geração de diversos impactos ambientais, este estudo analisa a influência da utilização de areia de praia em substituição à areia proveniente de leito de rio na produção de argamassas de revestimento. A partir da areia de rio, foram
Matéria (Rio J.). Publicado em: 10/06/2019