Flexural Behavior
Mostrando 1-12 de 95 artigos, teses e dissertações.
-
1. Mechanical properties and fractography of cement-based composites reinforced by natural piassava and jute fibers
Abstract Today’s demand for environmentally friendly and energy-efficient solutions to the construction industry has driven researchers to match natural resources with traditional technics to develop new building technologies. However, there are literature limitations about the correlation of fiber-matrix interface with the failure of natural fibers in mor
Cerâmica. Publicado em: 2022
-
2. Evaluation of the Effect of the Incorporation of Blends of Fuel and Fluxing Wastes in Red Clay Ceramics
The clay samples endure the incorporation of industrial and urban wastes, which do not cause large variations in their properties if added in controlled quantities. Wastes can be classified as fuel, fluxing and property affecting wastes. The fuel wastes usually have a high amount of organic matter, that when heated cause exothermic reactions, releasing heat
Mat. Res.. Publicado em: 09/12/2019
-
3. Glass-ceramic produced with recycled glass
ABSTRACT The objective of this work is the production and characterization of glass-ceramic with recycled glass powder and 4% (w/w) of cerium dioxide. Eleven groups were defined with conformation pressure of 11.6 and 25.8 MPa, and cerium dioxide addition. The sintering temperatures of 650, 675, 700 and 750 °C were used. The raw material was formed into a mo
Matéria (Rio J.). Publicado em: 25/11/2019
-
4. Bond strength evaluation between textiles reinforced mortar with carbon nanotubes and concrete substrate
Abstract The influence of using carbon nanotubes to improve bond strength between textiles reinforced mortar and concrete was investigated. Forty-two specimens were tested using double-shear test to evaluate the effect of various parameters such as CNTs addition, type of textile material, bond length and width, and number of TRM layers on the bond behavior.
Lat. Am. j. solids struct.. Publicado em: 25/11/2019
-
5. Avaliação do comportamento de estanqueidade à água de argamassas e hidrorrepelentes – Parte II
RESUMO Além da função estética, os revestimentos de fachada protegem as edificações da penetração de água e, consequentemente, diminuem a propensão ao surgimento de manifestações patológicas que levariam à degradação da superfície. Este trabalho apresenta os ensaios de avaliação do comportamento de estanqueidade à água de revestimentos a
Matéria (Rio J.). Publicado em: 25/11/2019
-
6. Experimental study of reinforced masonry beams
Resumo Com objetivo de contribuir com o melhor entendimento do comportamento de vigas de alvenaria estrutural armada, foi realizado o estudo experimental de vigas de alvenaria armada com blocos de concreto. Essas foram projetadas para ruptura à flexão, sendo analisando o modo de fissuração, a flecha, o momento fletor último, a deformação por encurtame
Rev. IBRACON Estrut. Mater.. Publicado em: 11/11/2019
-
7. Structural models for analysis of reinforced concrete frame buildings with masonry infills
Resumo Este trabalho tem como objetivo o estudo do comportamento de pórticos de edifícios de concreto armado preenchidos com alvenaria frente às ações horizontais, empregando-se dois modelos estruturais: i) modelo de diagonal equivalente (MDE) e ii) modelo com elementos finitos bidimensionais para estado plano de tensões (MEF). No primeiro modelo, a al
Rev. IBRACON Estrut. Mater.. Publicado em: 11/11/2019
-
8. Flexural behavior of hybrid GFRP - concrete railway sleepers
Resumo Este trabalho tem por objetivo apresentar o comportamento à flexão de vigas híbridas de GFRP (glass fiber reinforced polymer - polímero reforçado com fibra de vidro) e concreto para aplicação em dormentes ferroviários. Pretendeu-se obter dormentes com adequada resistência mecânica, não susceptíveis à corrosão, duráveis e mais leves que
Rev. IBRACON Estrut. Mater.. Publicado em: 23/09/2019
-
9. Estudo da substituição do nylon por compósito de polipropileno com fibra de vidro
RESUMO Peças fabricadas com polímeros de alto desempenho têm sido substituídas por materiais similares, sendo produzidas com uma composição de polipropileno (PP), que tem um custo mais baixo. Uma das composições mais comumente utilizadas é a junção do polipropileno com fibras, resultando na formação de um novo material, com características dife
Matéria (Rio J.). Publicado em: 16/09/2019
-
10. Pervious concrete made with electric furnace slag (FEA): mechanical and hydraulic properties
Resumo O objetivo deste trabalho é viabilizar o uso de escória de forno elétrico (FEA) em substituição ao agregado graúdo convencional na fabricação de concreto permeável (CoPe), atingindo os parâmetros mínimos exigidos pela norma NBR16416/2015. Esta substituição minimizaria a utilização de agregados naturais, além de aproveitar um resíduo q
Rev. IBRACON Estrut. Mater.. Publicado em: 18/07/2019
-
11. The effect of concentrated transversal force on the moment resistance of rectangular hollow steel section beams
Abstract This article reports on a preliminary investigation about the effect of concentrated transversal force on the bending moment resistance of rectangular hollow steel section (RHS) beams. Two six-meter-long specimens with yield strength of 300 MPa and cross-section size of 250×150×6.4 mm were subjected to bending tests using a four-point load configu
REM, Int. Eng. J.. Publicado em: 19/06/2019
-
12. The influence of fiber size on the behavior of the araucaria pine nut shell/PU composite
Abstract The use of araucaria pine nut shell in polymer composites may increase the pine nut value and help protec araucaria (Araucaria angustifolia) itself, which is an endangered species. The aim of this work is to study the influence of the size of pine nut shell fiber on the mechanical properties of composites made of this shell and polyurethane derived
Polímeros. Publicado em: 10/06/2019