Force Plate
Mostrando 1-12 de 72 artigos, teses e dissertações.
-
1. DETERMINATION OF KINETIC ASYMMETRIES IN SOCCER PLAYERS PERFORMING VERTICAL JUMP: PROPOSAL OF A NOVEL PROCEDURE TO DETERMINE IMPULSE FROM FORCE PLATE DATA
RESUMO O primeiro objetivo do estudo foi comparar a assimetria do pico de força (Fpico) de membros inferiores em dois procedimentos de análise, simultâneo e sequencial, no salto com contramovimento (SCM) de futebolistas. Foram realizadas três séries de seis SCM em duas plataformas de força. Para o procedimento sequencial, os 18 SCM foram divididos em d
J. Phys. Educ.. Publicado em: 20/12/2019
-
2. Torsional comparative biomechanical test of modified tibial-plateau-leveling osteotomy plate and locking plate in canine synthetic tíbias
RESUMO O objetivo do presente estudo foi desenvolver placa de TPLO bloqueada modificada e avaliar, em ensaio de torção, a estabilização óssea proporcionada pelo implante desenvolvido comparativamente a método de fixação óssea convencional com placa reta bloqueada. As variáveis obtidas foram força máxima, ângulo no pico de torque e rigidez. Foram
Arq. Bras. Med. Vet. Zootec.. Publicado em: 28/10/2019
-
3. The effect of concentrated transversal force on the moment resistance of rectangular hollow steel section beams
Abstract This article reports on a preliminary investigation about the effect of concentrated transversal force on the bending moment resistance of rectangular hollow steel section (RHS) beams. Two six-meter-long specimens with yield strength of 300 MPa and cross-section size of 250×150×6.4 mm were subjected to bending tests using a four-point load configu
REM, Int. Eng. J.. Publicado em: 19/06/2019
-
4. Prediction of 3D ground reaction forces during gait based on accelerometer data
Abstract Introduction The aim of this study was to predict 3D ground reaction force signals based on accelerometer data during gait, using a feed-forward neural network (MLP). Methods Seventeen healthy subjects were instructed to walk at a self-selected speed with a 3D accelerometer attached to the distal and anterior part of the shank. A force plate was
Res. Biomed. Eng.. Publicado em: 21/09/2018
-
5. Investigation of Mechanical and Metallurgical Properties of Friction Stir Corner Welded Dissimilar Thickness AA5086-AA6061 Aluminium Alloys
In this investigation, an attempt has been made to fabricate dissimilar thickness corner joint using non-heat treatable (AA5086) and heat treatable (AA6061) dissimilar aluminium alloys by friction stir welding process with plate thicknesses of 6mm and 4mm. Three parameters and three levels were considered to conduct the experiments such as welding and rotati
Mat. Res.. Publicado em: 11/06/2018
-
6. Seismic Performance of Post-Northridge Welded Connections
Abstract Post-Northridge welded connections are widely used in engineering projects as lateral-force-resisting systems. In this study, we aim to assess the cyclic performance of the post-Northridge welded connections to compare the connections with each other. For this purpose, we focus on Welded Unreinforced Flange – Welded Web (WUF-W), Welded Flange Pla
Lat. Am. j. solids struct.. Publicado em: 26/04/2018
-
7. Carbon Fiber Reinforced Polymer and Epoxy Adhesive Tensile Test Failure Analysis Using Scanning Electron Microscopy
Morphological characteristics analysis before and after tensile tests were studied using scanning electron microscopy (SEM) technique to follow the failure evolution on carbon fiber reinforced polymer (CFRP) and epoxy resins. Micrograph analysis of CFRP plate before tensile test shows some intrinsic manufacturing defects, which can influence the mechanical p
Mat. Res.. Publicado em: 06/07/2017
-
8. Modulation of drug resistance and biofilm formation of Staphylococcus aureus isolated from the oral cavity of Tunisian children
Abstract Objectives: This study aims to investigate the antimicrobial and the anti-biofilm activities of Lactobacillus plantarum extract (LPE) against a panel of oral Staphylococcus aureus (n = 9) and S. aureus ATCC 25923. The in vitro ability of LPE to modulate bacterial resistance to tetracycline, benzalchonium chloride, and chlorhexidine were tested also
Braz J Infect Dis. Publicado em: 2017-02
-
9. Numerical Study on Steel Shear Walls with Sinusoidal Corrugated Plates
Abstract Over the past decades a growing demand and interest has stimulated many researchers to investigate different aspects of steel plate shear walls (SPSWs). The structural performance of steel shear walls with sinusoidal corrugated plate infills is investigated in this study. Finite element (FE) analysis was adopted using ANSYS software, wherein flat an
Lat. Am. j. solids struct.. Publicado em: 2016-12
-
10. Numerical Study on the Structural Performance of Steel Beams with Slant End-plate Connections
Abstract Thermal effects can be one of the most harmful conditions that any steel structure should expect throughout its service life. To counteract this effect, a new beam, with a capability to dissipate thermally induced axial force by slanting of end-plate connection at both ends, is proposed. The beam was examined in terms of its elastic mechanical behav
Lat. Am. j. solids struct.. Publicado em: 2016-07
-
11. Effect of a single session of ear acupuncture on pain intensity and postural control in individuals with chronic low back pain: a randomized controlled trial
ABSTRACT Background Ear Acupuncture (EA) is a form of acupuncture in which needles are applied to the external ear and has been used in multiple painful conditions. Low back pain (LBP) is highly prevalent in active individuals and causes high economic burden to health systems worldwide. LBP affects the person’s ability to keep balance, especially in chall
Braz. J. Phys. Ther.. Publicado em: 16/06/2016
-
12. Numerical Study on Ultimate Behaviour of Bolted End-Plate Steel Connections
Abstract Bolted end-plate steel connections have become more popular due to ease of fabrication. This paper presents a three dimension Finite Element Model (FEM), using the multi-purpose software ABAQUS, to study the effect of different geometrical parameters on the ultimate behavior of the connection. The proposed model takes into account material and geome
Lat. Am. j. solids struct.. Publicado em: 2016-01