Hardfacing
Mostrando 1-12 de 15 artigos, teses e dissertações.
-
1. Effect of Welding Parameters on Nanostructured Fe-(C, B)-(Cr, Nb) Alloys
New nanostructured Fe-(Nb,Cr)-(C,B) multicomponent alloys have been developed for hardfacing application. They have better wear resistance than traditional Fe-Cr-C alloys. The nano-alpha-Fe, eutectic and hard carboborides phases of the weld metal usually show variations with the welding procedure. 6 test samples with different heat input were welded. It was
Mat. Res.. Publicado em: 20/01/2020
-
2. Fundente para Recargue por Soldadura con Arco Sumergido a Partir de Ferrocromo-manganeso y Escoria de la Reducción Simultánea de Cromita y Pirolusita
Abstract The obtaining of a flux for hardfacing by Submerged Arc Welding (SAW), using ferrochrome-manganese and slag obtained from the simultaneous carbothermal reduction of chromite and pyrolusite is addressed. The ferrochrome-manganese and the slag were obtained, conceiving that both products satisfy the requirements of the components (alloy system and ma
Soldag. insp.. Publicado em: 24/10/2019
-
3. Influência da microestrutura na resistência ao desgaste microabrasivo de ligas de F-Cr-C e Fe-Cr-C-Nb
ABSTRACT Neste trabalho é feita uma avaliação da influência do teor de cromo e da combinação do cromo e nióbio em ligas de revestimento duro do tipo Fe-Cr-C, na microestrutura e propriedades que envolvam a resistência ao desgaste microabrasivo. Vários estudos têm sido realizados em busca de informações conclusivas sobre este sistema em condiçõe
Matéria (Rio J.). Publicado em: 20/05/2019
-
4. Effect of Bead Overlapping on the Microstructure and Mechanical Properties of CoCrWC Alloy Coatings
In order to protect industrial components, cobalt base alloys are applied as hardfacing material through welding techniques. A large number of papers have shown that controlling the chemical composition is a key point regarding the wear and corrosion resistance of coatings. This paper investigated the effect of bead overlapping on the microstructure and prop
Mat. Res.. Publicado em: 17/09/2018
-
5. Influence of Pushing and Pulling the Electrode Procedure and Addition of Second Layer of Welding on the Wear in Hardfacing of Fe-Cr-C
The aim of this work is evaluate the influence of welding conditions on abrasive wear resistance in coating of Fe-Cr-C. The metal base used in this investigation was the steel SAE 1020 and as welded metal the selfshilded tubular wires of Fe-Cr-C with 1.6 mm of diameter. The welding parameter such as amperage, voltage, welding speed, wire feed speed and the d
Mat. Res.. Publicado em: 19/09/2016
-
6. Microstructure and Abrasion Resistance of Fe-Cr-C and Fe-Cr-C-Nb Hardfacing Alloys Deposited by S-FCAW and Cold Solid Wires
Abstract This work assesses the wear resistance behavior of different high Cr and Nb alloyed hardfacing deposits carried out by Self-shielded Flux Cored Arc Welding, considering the resulting microstructures as base for the analysis. To obtain non-commercial alloys, an “in-situ” technique was employed with addition of cold wire into the weld pool. Six co
Soldag. insp.. Publicado em: 2016-09
-
7. Efecto de los parámetros de soldadura sobre la microestructura de recargues nanoestructurados base hierro depositados por FCAW-S
Lately modern hardfacing tubular wires for semiautomatic welding with gas protection and without it have been developed. These wires deposit Fe-based nanostructured alloys with high abrasive wear resistance. The information on these new consumables is scarce, especially about the effect that the welding parameters (heat input, shielding gas, arc voltage, cur
Soldag. insp.. Publicado em: 2014-12
-
8. Effect of processing on microstructure and properties of CoCrMoSi alloy
CoCrMoSi alloys microstructure is affected by processing and their properties have been associated with the high volume fraction of Laves phase. However, not much has been reported on the effect of structure refinement and morphology on the properties of these alloys. This paper evaluates a CoCrMoSi alloy processed by centrifugal casting and Plasma Transferr
Mat. Res.. Publicado em: 29/07/2013
-
9. Incertidumbre de la medición de masa en la determinación de los parámetros de consumo de electrodos de recargue
This work presents the evaluation of the uncertainty of the measurements to determine the consumption parameters of hardfacing electrode, emphasizing the mass measurement. The experimentation was carried out obtaining deposits at three levels of current (120 A, 145 A y 160 A) and measuring the time spent in welding, the length of the welds the test plate and
Soldag. insp.. Publicado em: 2013-06
-
10. Characterization of NiCrAlC PTA coatings
Surface tailoring with plasma transferred arc (PTA) hardfacing involves the deposition of powder mixtures to produce coatings with an almost unlimited chemical composition. PTA hardfacing is particularly important for processing low weldability alloys, such as those for high-temperature applications, of which NiCrAlC is an example. This study analyzed NiCrAl
Mat. Res.. Publicado em: 16/08/2012
-
11. Microstructural control of Co-based PTA coatings
Cobalt-based alloys are widely used as hardfacing materials when wear resistance is required at room temperature or high temperature applications. However, their performance is a consequence of their microstructures that depends on the processing conditions. This work focused on the influence of solidification rate on the structure development by processing
Mat. Res.. Publicado em: 16/08/2012
-
12. Effect of current and atomized grain size distribution on the solidification of Plasma Transferred Arc coatings
Plasma Transferred Arc (PTA) is the only thermal spray process that results in a metallurgical bond, being frequently described as a hardfacing process. The superior properties of coatings have been related to the fine microstructures obtained, which are finer than those processed under similar heat input with welding techniques using wire feedstock. This ob
Mat. Res.. Publicado em: 16/08/2012