Heat Flow
Mostrando 1-12 de 502 artigos, teses e dissertações.
-
1. COMPUTATIONAL ANALYSIS OF LOAD VENTILATION IN BROILER TRANSPORT
ABSTRACT The characterization of ventilation during the transport of broiler chickens is essential for identifying and characterizing the potential problems of a convective heat flow and its effects on the welfare and the health and production conditions of the chickens. The objective of this study was to evaluate the ventilation patterns in two layout model
Eng. Agríc.. Publicado em: 2021-02
-
2. Detection of seepage paths in small earth dams using the self-potential method (SP)
Abstract The application of geoelectric methods, such as induced polarization (IP), the electrical resistivity and the self-potential (SP), presents an important indirect study methodology in several areas of geology, such as mining, geotechnics and environmental geology. The present study deals with the results of the application of the self-potential metho
REM, Int. Eng. J.. Publicado em: 2020-09
-
3. PHYSICAL AND THERMAL PROPERTIES OF EUCALYPTUS WOOD CHARCOAL.
ABSTRACT The knowledge of the physical and thermal properties of eucalyptus charcoal is of fundamental importance in the design of equipment and development of cooling technologies. However, literature about physical properties for eucalyptus wood charcoal is largely unavailable, especially the thermal and aerodynamic properties, for the same material. The a
CERNE. Publicado em: 2020-03
-
4. WATER HOLDING CAPACITY AND HEAT TRANSFER ASPECTS OF A MIXTURE OF SUGAR CANE BAGASSE AND WHEAT BRAN IN A PARTIALLY FILLED ROTATING DRUM
Abstract Maximum water holding capacity of a mixture of sugarcane bagasse and wheat bran was determined in static conditions and in a drum rotated at 1 rpm. The variables filling degree, water flow rate, volume of added water and number of sprinklers were tested to control the moisture content of the solid and the number of rotations to achieve homogeneous m
Braz. J. Chem. Eng.. Publicado em: 09/12/2019
-
5. ENERGY AND EXERGETIC EVALUATION OF THE MULTICOMPONENT SEPARATION OF PETROCHEMICAL NAPHTHA IN FALLING FILM DISTILLATION COLUMNS
Abstract Multicomponent separation of synthetic petrochemical naphtha (hexane, cyclohexane, toluene and xylene) was carried out in a falling film distillation sequence with heat supply using a vapor chamber (thermosyphon). Tests were carried out by varying feed flow rate and temperatures of the feed and the vapor chamber in two ways of heat supply: isotherma
Braz. J. Chem. Eng.. Publicado em: 09/12/2019
-
6. Reconstruction of Precambrian terranes of Northeastern Brazil along Cambrian strike-slip faults: a new model of geodynamic evolution and gold metallogeny in the State of Bahia
Abstract The Precambrian basement of Northeastern Brazil is the product of Rhyacian block convergence. The main deformation and intrusion of crustal granitoids occurred between 2.15 and 1.8 Ga ago. This large area has been subjected to long-lasting and rather uniform stresses during the Cambrian period. Gold provinces in Bahia represent metallogenetic produc
Braz. J. Geol.. Publicado em: 21/10/2019
-
7. THERMAL PERFORMANCE OF ONE-PASS SHELL-AND-TUBE HEAT EXCHANGERS IN COUNTER-FLOW
Abstract A computational methodology is proposed and applied to calculate the temperature effectiveness, P, and the logarithmic mean temperature difference (LMTD) correction factor, F, of TEMA E shell-and-tube heat exchangers with one-pass and fluids flowing in counter-flow. An arbitrary number of baffles is considered along with three different mixture cond
Braz. J. Chem. Eng.. Publicado em: 30/09/2019
-
8. ENERGETIC ANALYSIS OF AN ABSORPTION CHILLER USING NH3/LiNO3 AS AN ALTERNATIVE WORKING FLUID
Abstract This paper presents a thermodynamic model developed for a prototype absorption chiller using NH3/LiNO3 with 10 kW of nominal capacity. The study was undertaken using thermodynamic modeling based on the mass and energy balance, takes the overall heat transfer coefficients into consideration and uses the characteristic equation method. First, the resu
Braz. J. Chem. Eng.. Publicado em: 30/09/2019
-
9. Effect of Welding Heat Input on the Microstructure and Mechanical Properties of Dissimilar Friction Stir-Welded Copper/Brass Lap Joint
Dissimilar lap welded joints of copper and brass metals were fabricated by friction stir welding (FSW) method at various welding heat inputs. The effect of welding heat inputs on the microstructure and mechanical properties of overlap welded joints at at two different join configurations (i.e. Advancing side and Retreating side joint configurations) was inve
Mat. Res.. Publicado em: 26/08/2019
-
10. Investigation of Thermal Parameters Effects on the Microstructure, Microhardness and Microsegregation of Cu-Sn alloy Directionally Solidified under Transient Heat Flow Conditions
The microstructure and mechanical properties of cast materials are strongly dependent on the thermal history during solidification process. The global casting industry has faced major challenges, i.e., customers increasingly demand completely finished cast parts as well as complexity of casting alloys are rising. Therefore, the previous knowledge the solidif
Mat. Res.. Publicado em: 19/08/2019
-
11. Influência do Regime Transiente Sobre a Microdureza e Microestrutura nos Aços ASTM-A36 e SAE-1045 Soldados pelo Processo MAG
Resumo O regime quase-estacionário pode não ser alcançado em soldagens a arco elétrico de peças de pequenas dimensões e/ou de materiais de maior condutividade térmica. Entretanto, o regime transiente sempre ocorrerá no início e no final da soldagem. Neste regime, a variação do fluxo de energia via calor pode promover variações microestruturais e
Soldag. insp.. Publicado em: 08/08/2019
-
12. EFFECT OF STEEL PLATE THICKNESSES AND FLUID FLOW CHARACTERISTICS OF AN IMPINGING AIR JET ON HEAT TRANSFER AT THE STAGNATION POINT
ABSTRACT The design and process of heat transfer elements, from its source to heat sink through various media vary according to the product and system concerned. The effect of thickness of a steel plate on heat transfer characteristics with an impinging air jet at the stagnation point was studied. Experiments were carried out with different nozzles, heights,
Braz. J. Chem. Eng.. Publicado em: 15/07/2019