Hybrid Software
Mostrando 1-12 de 68 artigos, teses e dissertações.
-
1. Novel Design of a Hybrid Superconducting Fault Current Limiter with Controlled Solid-State Device
Abstract Fault current limiters are essential devices used to protect the power system and its equipment against high levels of fault current, which are growing up due to the increase of new power sources. This paper proposes a novel design of a Hybrid Superconducting Fault Current Limiter (Hybrid SFCL), which is composed basically by thyristors in series wi
J. Microw. Optoelectron. Electromagn. Appl.. Publicado em: 2021-06
-
2. FEM-DEM simulation of Uniaxial Compressive Strength (UCS) laboratory tests
Abstract Finite/discrete element methods (FDEM) are hybrid numerical models that use algorithms to analyze the transition from continuous to discontinuous. This type of formulation allows modeling physical laboratory tests with greater proximity to reality. This article proposes to simulate the average behavior of a uniaxial compression test campaign. The te
REM, Int. Eng. J.. Publicado em: 2020-12
-
3. HYBRID SYSTEM SIMULATION TO SUPPLY HEATED AIR TO A SOLAR FOOD DRYER
ABSTRACT The intermittence of solar radiation, due to continuous rainy or cloudy days, is a limitation of simple and small solar dryers. These conditions often make them impossible to use. By including storage systems (thermal accumulation) and/or auxiliary energy sources, drying processes or dehydration can be conducted continuously, even during periods of
Eng. Agríc.. Publicado em: 2020-04
-
4. Oviposition preference and biological performance of Ceratitis capitata in Anacardiaceae, Cactaceae and Vitaceae fruit
RESUMO: O objetivo do estudo foi comparar a utilização de frutos de importância econômica e social para o nordeste do Brasil por Ceratitis capitata Wied. (Diptera: Tephritidae) para oviposição, desenvolvimento larval, tamanho e longevidade de adultos. Foram utilizados frutos de manga (Mangifera indica L.), quiabento (Pereskia bahiensis Gürke), palma-f
Arq. Inst. Biol.. Publicado em: 29/07/2019
-
5. FE Modeling and Seismic Performance Evaluation of Hybrid SMA-Steel RC Beam-Column Joints
Abstract Severe permanent deformations of buildings during earthquakes have been found as one of the major causes of the instability and failure of structures. The application of superelastic Shape Memory Alloy rebars at the plastic hinge region of reinforced concrete beam-column joints (SESMA-BCJs) can eliminate the seismic residual deformations. Such self-
Lat. Am. j. solids struct.. Publicado em: 27/06/2019
-
6. New hybrid approach for free vibration and stability analyses of axially functionally graded Euler-Bernoulli beams with variable cross-section resting on uniform Winkler-Pasternak foundation
Abstract In this paper, a new hybrid approach is presented based on the combination of the power series expansions and the Rayleigh-Ritz method for stability and free vibration analyses of axially functionally graded non-uniform beams resting on constant Winkler-Pasternak elastic foundation. In the proposed novel technique, the power series approximation is
Lat. Am. j. solids struct.. Publicado em: 08/04/2019
-
7. Physiological and biochemical changes during desiccation tolerance loss in millet (Pennisetum glaucum L.) seeds
ABSTRACT. The aim of this study was to evaluate the physiological and biochemical changes related to desiccation tolerance loss in millet seeds. The studied points of the germination process were determined according to the seed imbibition curve of the millet hybrid ADRF6010: control (0h), 3h of imbibition, 1 and 3 mm radicle. The seeds were dried on silica
Acta Sci., Agron.. Publicado em: 28/03/2019
-
8. Tomato seed image analysis during the maturation
Resumo: O potencial fisiológico das sementes está diretamente relacionado à normalidade do processo de formação delas, sob ponto de vista morfológico, estrutural e funcional. Deste modo, o objetivo deste trabalho foi avaliar a morfologia interna de sementes de tomate, híbrido BRS Nagai, em diferentes estádios de maturação, por meio da análise de i
J. Seed Sci.. Publicado em: 2019-01
-
9. Influence of ceramic material, thickness of restoration and cement layer on stress distribution of occlusal veneers
Abstract The aim of this study was to evaluate stress distribution in an occlusal veneer according to the restorative material, restoration thickness, and cement layer thickness. A tridimensional model of a human maxillary first molar with an occlusal veneer preparation was constructed using a modeling software of finite element analysis. The model was repli
Braz. oral res.. Publicado em: 29/11/2018
-
10. Hybrid Approach of Aortic Diseases: Zone 1 Delivery and Volumetric Analysis on the Descending Aorta
Abstract Introduction: Conventional techniques of surgical correction of arch and descending aortic diseases remains as high-risk procedures. Endovascular treatments of abdominal and descending thoracic aorta have lower surgical risk. Evolution of both techniques - open debranching of the arch and endovascular approach of the descending aorta - may extend a
Braz. J. Cardiovasc. Surg.. Publicado em: 2017-10
-
11. Dry Sliding Wear Behaviour of Aluminium 5059/SiC/MoS2 Hybrid Metal Matrix Composites
The present study is to investigate the influence of weight percentage of silicon carbide (SiC) (5,10 %, 15%) and particle size (10,20,40µm) of SiC and constant 2% of Molybdenum disulphide(MoS2)is reinforced with aluminium matrix. Wear performance of the composite was carried out through pin-on-disc method to calculate friction coefficient and wear resistan
Mat. Res.. Publicado em: 28/09/2017
-
12. Design of a Nanosatellite Ground Monitoring and Control Software – a Case Study
ABSTRACT The growing countries that have carried out the development of CubeSat missions for academic purposes do not offer aerospace engineering programs at their universities. This causes difficulties for traditional engineers upon the formal use of different standards and frameworks for aerospace development, such as the European Cooperation for Space Sta
J. Aerosp. Technol. Manag.. Publicado em: 2016-06