Laser Surface Treatment
Mostrando 1-12 de 91 artigos, teses e dissertações.
-
1. Efeitos do Processo de Refusão a Laser na Microestrutura e No Comportamento de Desgaste do Revestimento de WC Aspergido com HVOF
RESUMO O desgaste de componentes e equipamentos industriais e agrícolas representa um grande fator de depreciação de capital e de fonte de despesas com manutenção e reposição de componentes mecânicos. Como o desgaste é um fenômeno essencialmente superficial, envolvendo a remoção mecânica indesejável de material de superfícies, a solução estu
Matéria (Rio J.). Publicado em: 25/11/2019
-
2. Moringa oleifera seed as a natural coagulant to treat low-turbidity water by in-line filtration
Resumo O objetivo deste estudo é avaliar o uso de semente de Moringa oleifera (MO) como um coagulante natural para remoção de turbidez e cor aparente no tratamento de água de abastecimento com baixa turbidez inicial via técnica de filtração direta em linha. A morfologia e carga de superfície foram investigadas por técnicas de caracterização como m
Rev. Ambient. Água. Publicado em: 25/11/2019
-
3. Losartan improves alveolar bone dynamics in normotensive rats but not in hypertensive rats
Abstract Hypertension is one of the main causes of premature death in the world; also, it is associated with several bone alterations. Preclinical studies have demonstrated delayed alveolar bone healing in hypertensive rats. However, losartan has been favorable for consolidation of bone grafts and reduction in active periodontitis. Therefore, losartan is sug
J. Appl. Oral Sci.. Publicado em: 07/10/2019
-
4. Additive manufacturing of titanium alloy could modify the pathogenic microbial profile: an in vitro study
Abstract Additive manufacturing (AM) is an emerging process for biomaterials and medical devices. Direct Laser Metal Sintering (DLMS) is an AM technique used to fabricate Ti–6Al–4V implant materials with enhanced surface-related properties compared with wrought samples; thus, this technique could influence microbial adsorption and colonization. Therefore
Braz. oral res.. Publicado em: 30/09/2019
-
5. Assessment of the Fatigue Behavior of Ti-6Al-4V ELI Alloy with Surface Treated by Nd:YAG Laser Irradiation
The effect of a surface treatment by Nd:YAG laser irradiation on the fatigue behavior of Ti-6Al-4V ELI was studied. Axial fatigue tests were performed to obtain S-N curves in polished and laser treated conditions. Roughness measurements and scanning electron microscopy were used to characterize the features of the modified surface. A reduction in the fatigue
Mat. Res.. Publicado em: 05/09/2019
-
6. Microhardness and Ultrastructure of Demineralized Gamma-Irradiated Human Enamel after Diode Laser (980 nm) and Fluoride Surface Treatment
Abstract Quality of life drastically diminished after radiotherapy due to radiation induced oral complications. Fluoride was found to be helpful in decreasing the incidence of radiation caries; however it has not led to elimination of dental caries. Thus, new techniques containing low fluoride concentration or not containing fluoride at all, as laser irradia
Braz. arch. biol. technol.. Publicado em: 12/08/2019
-
7. Decomposition Rate, pH, and Enamel Color Alteration of At-Home and In-Office Bleaching Agents
Resumo Este estudo avaliou a taxa de decomposição (DR), pH, alteração da cor do esmalte (∆E) e índice de clareamento (DWI) promovido por agentes clareadores caseiros e de consultório. A superfície do esmalte foi submetida a (n=10): agentes caseiros (10%, 15%, 20% de peróxido de carbamida - CP e 6% de peróxido de hidrogênio - HP) e três agentes a
Braz. Dent. J.. Publicado em: 22/07/2019
-
8. Effects of Gas Nitriding on Fatigue and Crack Initiation of Ti6Al4V produced by Selective Laser Melting
Selective laser melting (SLM) is an additive manufacturing technique which permits fabrication of three dimensional parts by selectively melting consecutive layers of metallic powder. This allows the production of parts with high geometrical complexity. Titanium alloy Ti-6Al-4V (Ti64) is widely used in industry due to its high strength-to-mass ratio, corrosi
Mat. Res.. Publicado em: 15/07/2019
-
9. Influence of a Femtosecond Laser Surface Modification on the Fatigue Behavior of Ti-6Al-4V ELI Alloy
The objective of this investigation was to evaluate the influence of surface modification by femtosecond laser (with average fluence of 0.6 J/cm2 and scanning speed of 0.1 mm/s) on the fatigue resistance of Ti-6Al-4V ELI alloy. A significant reduction in the fatigue strength of the material modified by laser was observed. Residual tensile stresses generated
Mat. Res.. Publicado em: 01/07/2019
-
10. Beneficial Effects of Ethyl-Cyanoacrylate Coating Against Candida Albicans Biofilm Formation
Resumo O objetivo deste estudo foi verificar se as modificações feitas com o adesivo etil cianoacrilato, ECA (Super Bonder ®, Loctite, Itapevi, SP, Brasil) sobre as resinas acrílicas para reembasamento, poderiam inibir ou reduzir a formação de biofilmes de C.albicans sobre sua superfície quando comparado com um selante de superfície comercial (BisCov
Braz. Dent. J.. Publicado em: 03/06/2019
-
11. Fatigue Failure Analysis on Precracked 304 Stainless Steel Components Repaired by Laser with Addition of Nanocomposites
Abstract The service life of components can be extended by repairing fatigue crack with laser so as to improve resource utilization rate. However, the effect of laser repair may be influenced by the instability of laser treatment. To investigate the addition of nanocomposites on the laser repairing effect, fatigue test under uniaxial tension was carried out
Soldag. insp.. Publicado em: 16/05/2019
-
12. Improvement of Polypropylene Adhesion by Kraft Lignin Incorporation
Low surface energy and poor adhesion are well-known characteristics of polypropylene (PP). Surface treatments such as plasma, corona, and laser are usually applied to overcome these limitations. However, current studies highlight the incorporation of hydrophilic or amphiphilic polymers into hydrophobic low-surface-energy polymers as an alternative for increa
Mat. Res.. Publicado em: 25/02/2019