Linear And Nonlinear Programming
Mostrando 1-12 de 95 artigos, teses e dissertações.
-
1. Optimized dimensioning of steel-concrete composite beams
Resumo As seções mistas de aço e concreto estão cada vez mais sendo utilizadas na construção civil, tanto no cenário mundial quanto no Brasil. O trabalho conjunto do perfil de aço e da laje de concreto aumenta consideravelmente o desempenho do elemento estrutural misto devido ao aproveitamento das vantagens de cada material. Neste trabalho, é utiliz
Rev. IBRACON Estrut. Mater.. Publicado em: 13/12/2019
-
2. Performance and Egg Quality of Commercial Laying Hens Fed Diets Formulated Using Non-Linear Programming
ABSTRACT Feed formulation using linear programming consists of determining the mixture of feedstuffs required to meet pre-established animal nutritional requirements at the lowest cost. On the other hand, with the use of non-linear programming, it is possible to define nutritional requirements at the time of formulation, aiming at maximum profit. The objecti
Braz. J. Poult. Sci.. Publicado em: 25/11/2019
-
3. The electric boat charging problem
Abstract Paper aims This paper studies a new optimization problem called the Electric Boat Charging Problem (EBCP), which is based on the application of electric mobility in a river transport operation problem. Originality This work pioneers the studies of the electric mobility on the river operations, by proposing the EBCP. This problem includes real feat
Prod.. Publicado em: 23/09/2019
-
4. Sistema computadorizado para deslocamento de amostra com motor de passo utilizando o L298: aplicação na técnica de varredura-Z
Resumo Neste trabalho vamos abordar uma nova tecnologia, de baixo custo, de controle de motor de passo via computador, a qual pode ser utilizada para movimentação de amostras. Mais especificamente, desenvolvemos um sistema de controle usando o módulo eletrônico comercial L298, que evita o uso de um circuito eletrônico tradicional complexo de múltiplos
Rev. Bras. Ensino Fís.. Publicado em: 18/04/2019
-
5. Optimization of reinforced concrete polygonal sections under biaxial bending with axial force
Abstract Concrete is the world’s most utilized material for production of the structural elements employed in civil construction. Due to its low tensile strength and brittle nature it is reinforced with steel bars forming the reinforced concrete (RC structure). Linear elements of reinforced concrete are commonly employed in multi-story buildings, bridges,
Lat. Am. j. solids struct.. Publicado em: 04/10/2018
-
6. AN OPTIMIZATION MODEL TO MINIMIZE THE EXPECTED END-TO-END TRANSMISSION TIME IN WIRELESS MESH NETWORKS
ABSTRACT Time metrics are extremely important to evaluate the transmission performance on Wireless Mesh Networks (WMNs), whose main characteristic is to use multihop technology to extend the network coverage area. One of such metrics is WCETT (Weighted Cumulative Expected Transmission Time), in which transmission times per hop are weighted for both proactive
Pesqui. Oper.. Publicado em: 2017-08
-
7. Identifying Mechanical Properties of Viscoelastic Materials in Time Domain Using the Fractional Zener Model
Abstract The present paper aims at presenting a methodology for characterizing viscoelastic materials in time domain, taking into account the fractional Zener constitutive model and the influence of temperature through Williams, Landel, and Ferry’s model. To that effect, a set of points obtained experimentally through uniaxial tensile tests with different
Lat. Am. j. solids struct.. Publicado em: 2017-01
-
8. Solving the Integrated Schedule Generation and Fleet Assignment Problem: an ACOBased Metaheuristic Approach
Abstract Traditionally, the initial steps on airline planning – Schedule Generation and Fleet Assignment problems – are solved separately. This traditional approach usually leads to suboptimal solutions, since flight profitability – the decision criteria to schedule a flight – depends on what aircraft type will be used on that flight. On the other ha
J. Transp. Lit.. Publicado em: 2015-09
-
9. LINEAR AND NONLINEAR SEMIDEFINITE PROGRAMMING
This paper provides a short introduction to optimization problems with semidefinite constraints. Basic duality and optimality conditions are presented. For linear semidefinite programming some advances by dealing with degeneracy and the semidefinite facial reduction are discussed. Two relatively recent areas of application are presented. Finally a short over
Pesqui. Oper.. Publicado em: 2014-12
-
10. OPTIMIZATION WITH LINEAR COMPLEMENTARITY CONSTRAINTS
A Mathematical Program with Linear Complementarity Constraints (MPLCC) is an optimization problem where a continuously differentiable function is minimized on a set defined by linear constraints and complementarity conditions on pairs of complementary variables. This problem finds many applications in several areas of science, engineering and economics and i
Pesqui. Oper.. Publicado em: 2014-12
-
11. A Mixed-Integer convex formulation for production optimization of gas-lifted oil fields with routing and pressure constraints
Production optimization of gas-lifted oil fields under facility, routing, and pressure constraints has attracted the attention of researchers and practitioners for its scientific challenges and economic impact. The available methods fall into one of two categories: nonlinear or piecewise-linear approaches. The nonlinear methods optimize simulation models dir
Braz. J. Chem. Eng.. Publicado em: 2014-06
-
12. Estimação e previsão da estrutura a termo das taxas de juros usando técnicas de inteligência computacional / Term structure of interest rate modeling and forecasting using computational intelligence techniques
This work proposes the term structure of interest rates modeling and forecasting using computational intelligence techniques, based on data from the US and Brazilian fixed income markets. The yield curve modeling includes the use of some evolutionary computation methods like Genetic Algorithms, Differential Evolution and Evolution Strategies in comparison wi
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 25/06/2012