Machining Time
Mostrando 1-12 de 36 artigos, teses e dissertações.
-
1. Productivity and Superficial Quality of an Aspherical Die Using CAD/CAM
ABSTRACT Nowadays, it is hard to imagine modern industry without the manufacturing and design software aided by computer, known as CAD/CAM, once the search for excellence in complex geometry parts, reduced time, quality assurance and interchangeability is increasing. Within this quest, the CAD/CAM platform has become a significant factor in manufacturing, es
Matéria (Rio J.). Publicado em: 16/09/2019
-
2. Corrosion Behavior of AA7075-T73 Aluminum Alloy During Machining of Aeronautical Components
Corrosion of AA7075-T73 aluminum alloy during machining process was studied. An experimental device was proposed in order to simulate machining procedure. A design of experiments - DOE was used in order to evaluate what process parameter is significant. Some electrochemical tests based on open-circuit potential vs time measurements and potentiodynamic polari
Mat. Res.. Publicado em: 01/07/2019
-
3. Performance and Surface Integrity of Wire Electrical Discharge Machining of Thin Ti6al4v Plate Using Coated and Uncoated Wires
Wire Electrical Discharge Machining (WEDM) is one of the most important production technologies to manufacture very accurate small components and tools on any electrical conductive material. Titanium and its alloys have been widely used in automobile and aerospace industry as well as in medical engineering field. Small components and tools with complex geome
Mat. Res.. Publicado em: 03/06/2019
-
4. Surface Integrity Analisys in the Hard Turning of Cemented Steel AISI 4317
This work was based on the surface integrity analysis of hardened steel, AISI 4317 case carburized, quenched and tempered with 58 HRC, obtained by a turning operation executed with CBN (cubic boron nitride) tool, varying three basic cutting parameters (cutting speed, feed rate and cutting depth). The surface integrity characterization was conducted analyzing
Mat. Res.. Publicado em: 26/07/2018
-
5. Estudio de los parámetros de proceso del anodizado por plasma químico en Ti-6Al-4V ELI para implantes dentales
ABSTRACT In order to study the variation effect of some parameters of micro-arc oxidation process (MAO) on Ti-6Al-4V samples for dental implants, several treatments were carried out under different conditions of current density, exposure time and electrolyte chemical composition. These processes resulted in generated bioactive titanium oxide surface coatings
Matéria (Rio J.). Publicado em: 19/07/2018
-
6. Estudio del comportamiento de fundición CADI sometida a FCR
ABSTRACT Ductile Iron (DI) is a development of the iron alloys introduced in the ´50s, with free graphite in the form of nodules. Austempered Ductile Iron (ADI) is a development of DI later introduced, consisting on austempering heat treatment in order to obtain a high strength and high toughness material. Carbidic Austempered Ductile Iron (CADI) is a more
Matéria (Rio J.). Publicado em: 19/07/2018
-
7. Residual Stresses Analysis in Ball end Milling of Nickel-Based Superalloy Inconel 718
Inconel 718 is widely used in the aviation, space, automotive and biomedical industries because of its outstanding properties. Near-surface residual stresses that are induced by ball end milling in Inconel 718 can be crucial for the performance and service time of the machined parts. In this paper, the influences of cutting conditions, including the use of c
Mat. Res.. Publicado em: 18/09/2017
-
8. Investigation of High-Speed Cryogenic Machining Based on Finite Element Approach
Abstract The simulation of cryogenic machining process because of using a three-dimensional model and high process duration time in the finite element method, have been studied rarely. In this study, to overcome this limitation, a 2.5D finite element model using the commercial finite element software ABAQUS has been developed for the cryogenic machining proc
Lat. Am. j. solids struct.. Publicado em: 2017-03
-
9. Surface Integrity Analysis in Machining of Hardened AISI 4140 Steel
This study aimed to analyze the residual stresses and roughness in finishing milling of AISI 4140 steel, quenched and tempered up to hardness of 58 HRC. Machining operations were performed with the use of CBN inserts and by varying three basic cutting parameters (cutting speed, feed per tooth and cutting depth). Hardened materials are typically machined by a
Mat. Res.. Publicado em: 23/01/2017
-
10. Effect of Cold Work on Cavitation Resistance of an Austenitic Stainless Steel Coating
Abstract Machining procedures of welding deposits are usual and result on cold work hardened surfaces. The cold work effect on cavitation erosion of an austenitic stainless steel surface is assessed. FeCrMnSiB coatings were processed by PTA on AISI 304 plates. Specimens were grouped as the cold work deformed surface (CWHS) and the undeformed polished surface
Mat. Res.. Publicado em: 01/08/2016
-
11. Evolución Microestructural en Uniones de la Aleación Ti-6Al-4V Mediante el Proceso de Soldadura de Punto por Fricción-agitación
Abstract Friction stir spot welding (FSSW) is a process of recent development and interest, mainly in titanium alloys, since there are previous studies of aluminum alloys, magnesium, steel and polymers. Titanium alloys have a wide range of applications in the aeronautical industry, mainly in the components of commercial aircrafts as landing gear. Therefore,
Soldag. insp.. Publicado em: 2016-06
-
12. Machinability Evaluation in Hard Milling of AISI D2 Steel
Milling of hardened steel components provides considerable benefits in terms of reduced manufacturing cost and time compared to traditional machining. Temperature variation in milling is an important factor affecting the wear of cutting tools. The poor selection of milling parameters may cause excessive tool wear and increased work surface roughness. Hence,
Mat. Res.. Publicado em: 01/03/2016