Milling Process
Mostrando 1-12 de 136 artigos, teses e dissertações.
-
1. Obtainment of a new metal matrix composite from the recycling of UNS S31803 duplex stainless steel by powder metallurgy
Abstract The purpose of circular economy is to maximize resources efficiency. With the increase in consumption of raw materials, energy and waste generation, recycling is necessary for environmental and industrial reasons. Thus, the powder metallurgy, together with mechanical milling, stands as a new method for scraps recycling. This study aimed to produce U
REM - International Engineering Journal. Publicado em: 2022
-
2. Tuning the Photocatalytic Activity of Tin Oxide through Mechanical Surface Activation
Tin oxide (SnO2) nanoparticles were synthesized by the co-precipitation method and mechanically modified by high-energy ball milling. The experimental results demonstrate that the collision with zirconia balls produces slight changes in the crystalline, electronic, morphological, and surface properties of SnO2, which lead to an increase in the redox potentia
Journal of the Brazilian Chemical Society. Publicado em: 2022
-
3. Purification of raw palygorskite: a comparative study involving different processes and dispersing agents
Abstract Palygorskite (Pal) is a natural clay mineral with fibrous morphology and high surface area. Depending on the geological origin, it presents impurities, such as quartz and carbonates, which can harm some of its properties. Therefore, this work seeks to define a viable methodology for the purification of a Brazilian Pal. Two types of mixing processes
Cerâmica. Publicado em: 2021-06
-
4. Preparation and characterization of yttria stabilized zirconia (YSZ) films deposited by dip-coating on LSM-YSZ substrate with different proportions
ABSTRACT In this work, sol-gel/dip-coating process for obtaining yttria stabilized zirconia (YSZ, ZrO2–8% Y2O3) films deposited onto LSM-YSZ (lanthanum strontium manganite (LSM, La0.7Sr0.3MnO3) mixed with YSZ) with different proportions (20/80, 50/50, 80/20) was investigated. The films were deposited on substrate varying the number of layers deposited. LSM
Matéria (Rio J.). Publicado em: 25/11/2019
-
5. Variation of the milling conditions in the obtaining of nanocellulose from the paper sludge
ABSTRACT This work aimed to evaluate three different milling conditions, seeking the optimization of CNS isolation process. The paper sludge was chemically treated with detergent and H2O2, by two steps, to remove the noncellulosic contents (hemicellulose and lignin). After these treatments, the sample was milled with the variation of a liquid medium. The thr
Matéria (Rio J.). Publicado em: 16/09/2019
-
6. Effect of moisture content of two paddy varieties on the physical and cooked properties of produced rice
Resumo Yasemin e Amber são as principais variedades de arroz cultivadas no Iraque. A variedade Amber é a favorita por causa de seu sabor único, enquanto a Yasemin é a mais cultivada. O objetivo do presente estudo foi determinar o teor de umidade adequado para ambas as variedades, na obtenção da melhor taxa de extração (menor quebra), brancura e quali
Braz. J. Food Technol.. Publicado em: 01/08/2019
-
7. Mathematical drying kinetics modeling of jackfruit seeds (Artocarpus heterophyllus Lam.)
RESUMO A jaca (Artocarpus heterophyllus Lam.) é uma fruta com polpa rica em carboidratos, cálcio, fósforo, ferro e vitaminas do complexo B. No processamento da polpa é gerada uma grande quantidade de resíduos, onde incluem-se as sementes. Consumidas após cozimento, podem também passar por torra, moagem e incorporação em produtos de panificação. Co
Rev. Ciênc. Agron.. Publicado em: 04/07/2019
-
8. Analysis of the densification of a composite obtained by sintering process of aluminum bronze powders with different carbides
Abstract Aluminum bronze alloy is applied in environments that require materials of high mechanical resistance and wear, such as marine, oil & gas and aerospace ones. This study analyzes the densification of composites based on aluminum bronze with additions of the vanadium (VC) and niobium (NbC) carbides, and the influence of these carbides in the milling e
REM, Int. Eng. J.. Publicado em: 19/06/2019
-
9. Resistência mecânica à adesão em superfícies de madeira de pinus aplainadas e unidas por adesivos PVAc
RESUMO Este trabalho teve como objetivo analisar o desempenho de juntas coladas de madeiras da espécie Pinus elliottii com a utilização de dois adesivos comerciais à base de poliacetato de vinila (PVAc), com diferentes características físicas e composição química, ambos testados nas formas diluída em água e não diluída. As superfícies dos corpo
Matéria (Rio J.). Publicado em: 20/05/2019
-
10. Effect of Surfactant in Particle Shape and Thermal Degradation of Eggshell Particles
High energy ball milling and sonofragmentation were used successfully to reduce the crystallite size of calcium carbonate extracted from the eggshell. The ceramic was milled using either deionized water or stearic acid and then subjected to a subsequent size reduction by means of a tip horn. The thermal degradation of particles was influenced by the presence
Mat. Res.. Publicado em: 25/04/2019
-
11. Study on elastoplastic coupling mechanics model of the milled mixture of sugar cane
Abstract At present, the phenomenon of elastoplastic coupling isn’t considered in establishing the mechanics model of the milled mixture of sugar cane. In order to describe elastoplastic coupling and yield characteristics, based on uniaxial confined compression tests and direct shear tests, the evolution of the elastic parameters of the solid fiber with v
Food Sci. Technol. Publicado em: 11/04/2019
-
12. A review of the benefits for comminution circuits offered by rock blasting
Abstract Rock blasting is the first phase of comminution, completed by mechanical means downstream in the crushing and milling phases. Nevertheless, mineral processers and blasters seldom work together. The total energy of mechanical comminution depends on feeding grain size and on the internal resistance of the material to grinding. Blasting heavily influen
REM, Int. Eng. J.. Publicado em: 2019-03