Minimum Design Cost
Mostrando 1-12 de 37 artigos, teses e dissertações.
-
1. Optimized dimensioning of steel-concrete composite beams
Resumo As seções mistas de aço e concreto estão cada vez mais sendo utilizadas na construção civil, tanto no cenário mundial quanto no Brasil. O trabalho conjunto do perfil de aço e da laje de concreto aumenta consideravelmente o desempenho do elemento estrutural misto devido ao aproveitamento das vantagens de cada material. Neste trabalho, é utiliz
Rev. IBRACON Estrut. Mater.. Publicado em: 13/12/2019
-
2. Medical centers location and specialists’ allocation: a healthcare planning case study
Abstract Paper aims To set the locations of new medical centers to meet the population’s secondary care needs, the additional number of specialists, equipment, and an installation sequence at municipalities. Originality We developed descriptive cost functions models and adopted aggregate data from official sources to set parameters of an integrated MILP
Prod.. Publicado em: 02/12/2019
-
3. Influence of Tillage Systems and Selective Herbicides on Weed Management and Productivity of Direct-Seeded Rice (Oryza sativa)
RESUMO: Plantas daninhas causam dano considerável à colheita de arroz. Para averiguar a influência de diferentes práticas de manejo de plantas daninhas sob diferentes sistemas de cultivo, um teste de campo foi conduzido durante 2014 -15. Como desenho experimental foram utilizados blocos inteiramente casualizados com parcelas subdivididas, cada uma de 6 x
Planta daninha. Publicado em: 30/09/2019
-
4. Análise bioeconômica de períodos de suplementação proteico-energética na estação seca para novilhas Nelore em pastagem diferida de Urochloa decumbens
RESUMO A suplementação proteico-energética (SPE) é uma estratégia adequada à bovinocultura de corte no período seco do ano, embora sua adoção equivocada possa comprometer seu benefício/custo. O objetivo deste estudo foi avaliar o desempenho de novilhas Nelore em pastagem diferida de Urochloa decumbens sob dois períodos de SPE, e realizar análise
Arq. Bras. Med. Vet. Zootec.. Publicado em: 14/06/2019
-
5. Optimal design of beam-column connections of plane steel frames using the component method
Abstract This paper presents a methodology for optimization of beam-column connections of plane steel frames. The objective is to obtain beam- column connections mechanically more efficient and with minimum cost by determination of the optimal dimensions for the components of the connection; satisfying mechanical constraints associated with the bending momen
Lat. Am. j. solids struct.. Publicado em: 29/10/2018
-
6. Design of the austempering heat treatment of a ductile iron differential case aided by computer simulation
Abstract Austempered ductile iron is frequently employed in the fabrication of automobile parts due to its good mechanical properties, and its simplicity and low cost of the manufacturing process. The heat treatment design is an important stage, in which parameters such as temperatures and durations are chosen according to the required microstructure, part
Lat. Am. j. solids struct.. Publicado em: 02/07/2018
-
7. COLUMN GENERATION BASED ALGORITHMS FOR THE CAPACITATED MULTI-LAYER NETWORK DESIGN WITH UNSPLITTABLE DEMANDS
ABSTRACT We investigate a variant of the Multi-Layer Network Design problem where minimum cost capacities have to be installed upon a virtual layer in such a way that (i) a set of traffic demands can be routed AND (ii) each capacity (subband) is assigned a route in the physical layer. The traffic demands cannot be splitted along several paths (nor even sever
Pesqui. Oper.. Publicado em: 2017-09
-
8. Comparison between linear and nonlinear systems of feed formulation for broilers
Two experiments were simultaneously carried out to compare feed formulation models: a linear model for minimum cost with a nonlinear model for maximum profitability for one-to 42-d-old broilers. One-d-old male or female Cobb 500 broilers (n=2368) were allocated to one of the two trials according to sex. The experiments were performed simultaneously in an exp
Rev. Bras. Cienc. Avic.. Publicado em: 2015-03
-
9. Optimization of Airfoils for Minimum Pitching Moment and Compressibility Drag Coefficients
ABSTRACT: This paper concerns a numerical optimization method for designing airfoils based on adjoint method. The goal of present work is to reduce the compressibility drag or pitching moment of transonic airfoils without compromising on the lift coefficient. A new cost function based on this requirement is defined and the corresponding adjoint equations are
J. Aerosp. Technol. Manag.. Publicado em: 2014-12
-
10. Replacement of corn by babassu mesocarp bran in diets for feedlot young bulls
Nutrient intake and digestibility and productive performance of 30 feedlot young bulls fed diets containing babassu mesocarp bran in replacement of corn were evaluated. Animals were distributed in a completely randomized design with five levels of replacement of corn by babassu mesocarp bran (BMB): 0, 250, 500, 750 and 1000 g/kg of dry matter, and six replic
R. Bras. Zootec.. Publicado em: 2013-03
-
11. Obtenção de chips de berinjela (Solanun melongena L.) mediante processo combinado de desidratação osmótica em solução ternária e secagem convectiva
This work aimed to utilize the combined osmotic dehydration and convective drying process to obtain eggplant chips by a non-conventional healthier and more low cost way. The combined process was studied through a factorial experimental design having as independent variables the temperature (30-50C), sucrose (27,5 to 42,5% w/w) and sodium chloride (3,75 to 6,
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 15/06/2012
-
12. Reliability-based design optimization strategies based on FORM: a review
In deterministic optimization, the uncertainties of the structural system (i.e. dimension, model, material, loads, etc) are not explicitly taken into account. Hence, resulting optimal solutions may lead to reduced reliability levels. The objective of reliability based design optimization (RBDO) is to optimize structures guaranteeing that a minimum level of r
J. Braz. Soc. Mech. Sci. & Eng.. Publicado em: 2012-12