Ni Cr Alloys
Mostrando 1-12 de 79 artigos, teses e dissertações.
-
1. Systematic review and meta-analysis of welding procedures in one-piece cast implant-supported frameworks
Abstract The objective of this systematic review and meta-analysis was to evaluate the effect of welding techniques on implant-supported prostheses and determine whether they contribute to a better adaptation compared with a one-piece cast. A search was conducted using the PubMed/MEDLINE, Embase, and Cochrane Library databases, and articles published until N
Braz. oral res.. Publicado em: 25/11/2019
-
2. Potencial antimicrobiano de diferentes retentores intrarradiculares frente a Enterococcus faecalis: uma avaliação in vitro
Resumo Introdução O tratamento endodôntico tem como objetivo erradicar microrganismos bacterianos e fúngicos do canal radicular, ou pelo menos possibilitar sua redução para níveis compatíveis com a saúde do tecido perirradicular, uma vez que, após o tratamento endodôntico, colônias de microrganismos residuais podem estar presentes nos túbulos d
Rev. odontol. UNESP. Publicado em: 23/09/2019
-
3. Study of the metallurgical bond between 316 steel substrates and NiCrAlY coating sprayed by HVOF and irradiated with a low power CO2 laser
RESUMO Considerando a importância do desenvolvimento de novos materiais ao longo dos últimos anos; os pesquisadores vêm estudando soluções eficazes através do uso de revestimentos de alta dureza para aplicação em ferramentas de corte e matrizes de conformação. Revestimentos de carboneto de tungstênio (WC) são um dos mais utilizados em sistemas de
Matéria (Rio J.). Publicado em: 16/09/2019
-
4. Efecto de los parámetros de aplicación en recubrimientos de Ni-Cr-B-Fe-Si obtenidos por Flame Spray
ABSTRACT Surface damage of components in service is an issue of great industrial interest because of the costs associated to the replacement of certain critical components. There are several techniques to generate coatings, which provide increased resistance to a particular type of surface damage. In this way, it is achieved surface protection to different s
Matéria (Rio J.). Publicado em: 02/08/2018
-
5. Análisis de la forma de onda de señales de Emisión Acústica producida en ensayos de interfaces ceramo-metálicas
ABSTRACT The study of ceramic-metal interface is of special importance in odontology area by the current demand about dental prostheses, so it is very important to be more and more similar to natural teeth and with a long service life. With the aim of assessing in detail the behavior of ceramic-metal interface used in dental restorations systems, in this wor
Matéria (Rio J.). Publicado em: 19/07/2018
-
6. Hysteretic Behavior of Twin Boundary Peak Due to Precipitation in Co-Ni-Cr alloy
Anelastic behavior and microstructural changes of a Co-Ni-Cr super-alloy were monitored over the temperature range 250-950ºC, by using several complementary techniques. Two grades of this alloy were used, differing by the presence of small quantity of beryllium (<1.5% at.). Thermoelectric power reveals two distinct precipitation stages. The first precipitat
Mat. Res.. Publicado em: 02/07/2018
-
7. Lubricated Conditions Imposed on Coating Multi-layer on Wear Resistance Under Cr2O3 Effect
Lubricated pin-on-disk sliding wear tests were performed on applied to Al-0.1Mg-0.35Ni-Si Alloy by using the spray coating method has been investigated. Different loads were 5, 10, and 15 N at a sliding velocity, 1.32 m/s at room temperature and 60% relative humidity. The surfaces were analyzed by using X-ray diffraction the residual (XRD), energy dispersive
Mat. Res.. Publicado em: 16/04/2018
-
8. Tempering Temperature Influence on 13Cr4Ni0.02C Steel Corrosion Resistance
The thermal treatments employed in alloys are essential to obtaining desired microstructures and corrosion resistance properties. In this paper the low carbon martensitic steel 13Cr4Ni0.2C with different tempering temperatures was studied using potentiodynamic polarization technique in synthetic marine environment, in order to evaluate the effect of the temp
Mat. Res.. Publicado em: 13/11/2017
-
9. Fracture Modes of AISI Type 302 Stainless Steel Under Metastable Plastic Deformation
Martensitic transformation can be induced by plastic deformation in metastable iron-based alloys, such as stainless steels containing limited amounts of C, Ni and Cr. This transformation takes place at the temperature range from Ms and Md, usually at relatively lower temperature values. The transformed martensite has been associated with maximum ultimate str
Mat. Res.. Publicado em: 09/11/2017
-
10. Kinetics Oxidation and Characterization of Cyclically Oxidized Layers at High Temperatures for FeMnSiCrNiCe and FeSiCrNi Alloys
Conventional stainless steels are used in cyclic oxidation, but the high amount of Cr and mainly Ni increase the price of these alloys. The objective of the present study was to assess the cyclic oxidation resistance of FeSiCrNi and FeMnSiCrNiCe alloys in comparison to AISI 304 and AISI 310 stainless steels by evaluating the oxidation kinetics and using char
Mat. Res.. Publicado em: 18/09/2017
-
11. Development of a Material for Manufacturing a Mold for Plastic Injection
Injection molding is a process used to manufacture high volumes of plastic containers of complex geometric shapes. Although CuBe has always been used, there are currently some alternative alloys such as the CuNiSiCr alloy that has lower manufacturing cost and similar properties. The objective of this paper is to characterize, by techniques of microscopy, the
Mat. Res.. Publicado em: 07/08/2017
-
12. Embrittlement and Corrosion Decay of a Cast Duplex Stainless Steel
Duplex stainless steels (DSS) are Fe-Cr-Ni-Mo alloys, with low carbon content, which have a favorable combination of mechanical properties and corrosion resistance. These characteristics are mainly attributed to a dual phase and refined microstructure, typical of these alloys, consisting of similar amounts of ferrite and austenite. For this reason, DSS are w
Mat. Res.. Publicado em: 20/07/2017