Optimum Voltage
Mostrando 1-12 de 29 artigos, teses e dissertações.
-
1. Development of a generic method for the determination of proton-pump inhibitors by capillary zoneelectrophoresis
A generic capillary zone electrophoresis method was developed for the analysis of four proton pump inhibitors: omeprazole, pantoprazole, lansoprazole and rabeprazole. During preliminary analysis screening of phosphate buffers at different pH levels was performed, in order to determine the optimum pH domain suitable for the simultaneous determination of all s
Braz. J. Pharm. Sci.. Publicado em: 30/09/2019
-
2. Caracterización del proceso de fabricación de macroporos sobre sustrato de silicio por método electroquímico
ABSTRACT In the present work, the fabrication process of a set of micropores on crystalline silicon wafers manufactured through wet etching technique was studied. The influence of different control factors such as voltage, temperature and braking agent on the specific characteristics of formation was evaluated. An exhaustive analysis of the evolution of elec
Matéria (Rio J.). Publicado em: 19/07/2018
-
3. Bias voltage influence on the mechanical and tribological properties of titaniumaluminum nitride coatings produced by triode magnetron sputtering
TixAl1-xN coatings were grown using the triode magnetron sputtering technique with various bias voltages between -40 V and -150 V. As the bias voltage increased, an increase in the Al atomic percentage was observed, presenting a competition with Ti and producing structural changes. Moreover, the grain size and roughness were also strongly influenced by the b
Matéria (Rio J.). Publicado em: 2015-03
-
4. Augmentation of wear-protective coatings for non-ferrous alloys by the addition of Cr and Ni elements
A number of Al-, Mg- and Ti-base alloys were preconditioned by oxidation via Plasma-electrolytic oxidation (PEO) followed by the addition of Cr and Ni elements in the coating pores by chemical precipitation and a final stage of mechanical treatment. The overall effect was a combination of hardness and resistance to wear. PEO voltage level was found to be a f
Mat. Res.. Publicado em: 2014-12
-
5. A robustez de um sistema de distribuição e a alocação de medidores de qualidade da energia elétrica frente aos afundamentos de tensão / The robustness of a distribution system and an allocation of power quality monitors in the face of the voltage sags
This dissertation aims to initially reintroduce and spread the Fault Positions Method (FPM) as an analytic means to determine the remaining voltage in all bus bar constituents of a Distribution System (DS), upon the occurrence of voltage sags. By applying this method, it is possible to formulate the during fault voltage matrix, thus denoting the influence an
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 23/03/2012
-
6. ANALISE E PROJETO DO CONVERSOR BUCK INTERCALADO PARA ALIMENTAÇÃO DE LÂMPADAS DE DESCARGA EM ALTA PRESSÃO DE ALTA POTÊNCIA / INTERLEAVED BUCK CONVERTER ANALYSIS FOR HIGH POWER HIGH INTENSITY DISCHARGE LAMPS SUPPLYING
This work presents a detailed analysis about the interleaved buck converter applied to electronic ballasts to supply high power HID lamps, assuming the input voltage as a PFC stage output. As the output capacitor has a maximum value to be applied in parallel with the lamp, parallel operated converters are a suitable choice because the output current ripple c
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 29/02/2012
-
7. Optimizing surface finish in WEDM using the taguchi parameter design method
Wire electrical discharge machining (WEDM) is extensively used in machining of materials when precision is of major factor. Selection of optimum machining parameter combinations for obtaining higher accuracy is a challenging task in WEDM due to the presence of a large number of process variables and complex stochastic process mechanisms. In the present work,
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2010-06
-
8. Otimização da metodologia de determinação de molibdênio em solos e plantas por voltametria de onda quadrada com redissolução catódica adsortiva / Optimization of the molybdenum determination in soils and plant methodology by cathodic adsorptive stripping square- wave voltammetry
Molybdenum is an element essential to life that can be found practically in the whole biosphere. It is present in the nitrase enzyme cofactor and is responsible for the reduction of the N2 molecule and its fixation in the terrestrial crust. In other enzymes, molybdenum acts in reactions of transference of atoms of oxygen to a lot of sub-stratums. Molybdenum
Publicado em: 2008
-
9. Otimização da potencia de operação em sistema isolado fotovoltaico usado técnicas de inteligencia artificial / Power operation optmization of photovoltaic stand alone system using artificial intelligence techniques
This work presents a power operation optimization of photovoltaic stand alone system using artificial intelligence techniques, via a optimum voltage estimator and control systems to maintain the photovoltaic generator in the maximum power point. A Fuzzy Systems is implemented to estimate from instantaneus radiation and room temperature, the optimum voltage o
Publicado em: 2007
-
10. Methodology for monitoring voltage SAGs and SWELLs in power systems. / Metodologia para a monitoração eficiente de variações de tensão de curta duração em sistemas elétricos de potência.
This dissertation presents a methodology based on Genetic Algorithms and Fuzzy Mathematical Programming to determine the optimum number of power quality monitors and the locations they should be installed to measure Voltage Sags and Swells in transmission power networks. The methodology developed represents a tool for planning power networks, because it indi
Publicado em: 2007
-
11. Optimum sizing of units of generation distributed in radial systems of distribution through techniques of nonlinear programming. / Ajuste ótimo da potência inserida por unidades de geração distribuída em alimentadores de média tensão
The optimum sizing of units of Distributed Generation is a problem to which this formulation takes in consideration the reduction of losses in the distribution lines, the voltage control, the capacity (in MW) of the units respecting the operational limits of the system. The main objective of the sizing process is to determine the active and reactive power le
Publicado em: 2006
-
12. Perdas aparentes serie como criterio a ser minimizado no fluxo de potencia otimo reativo / Series apparent losses as a criterion to be minimized on reactive optimal power flow
The classic performance indexes, used on reactive power supply and voltage profile analysis, are the sum of active and series reactive power losses that occur on transmission systems, under determined load conditions. The minimization of active or reactive losses, changes significantly the reactive power supply required from the transmission system to suppor
Publicado em: 2006