Piston
Mostrando 1-12 de 64 artigos, teses e dissertações.
-
1. 3D numerical investigation of mixture formation and combustion in a DISI engine at part-load under stratified operation
This work investigates through numerical simulation, the operation of a big bore direct fuel injection spark ignition engine, at part load under stratified operation. It evaluates fuel-air mixture preparation and combustion process with the adoption of detailed chemical kinetics mechanisms for both Isooctane and Ethanol, and applying adaptive mesh refinement
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 2020
-
2. Investigation of the effect of nozzle design on rheological bioprinting properties using computational fluid dynamics
ABSTRACT Bioprinting is the utilization of techniques derived from three-dimensional printing to generate complex biological structures which may replace natural tissues or organs. It employs high spatial resolution deposition of different cell types, growth factors and biomaterials. Those together form bioinks, which are the bioprinting inputs, analogously
Matéria (Rio J.). Publicado em: 16/09/2019
-
3. Application of an alternative mesh morphing method on the numerical modeling of oscillating wave surge converters
RESUMO Uma das tecnologias capazes de explorar a energia das ondas, baseada na captação das componentes horizontais do movimento destas, aliada a um sistema placa-pistão, vem experimentando um notável desenvolvimento ao longo dos últimos anos, tal dispositivo é conhecido como conversor oscilante por translação de ondas. Este possui um grande potencia
RBRH. Publicado em: 29/07/2019
-
4. Calibration of high-temperature furnace assemblies for experiments between 200 and 600 MPa with end-loaded piston-cylinder apparatuses
Abstract We present pressure calibration results for piston-cylinder –” and 1” high temperature furnace assemblies in the 200-600 MPa range aiming to expand its applicability to simulate upper crustal conditions. The furnace assemblies were made up by crushable MgO, graphite heater, pyrex glass spacer, and NaCl sleeve. Twenty-one experiments were carri
Braz. J. Geol.. Publicado em: 15/04/2019
-
5. Extensión de durabilidad de pistones de bombas de fractura hidráulica mediante el empleo de tecnología de nitruración por plasma y PVD
ABSTRACT Hydraulic stimulation technique consists of "fracturing" the formation (rock reservoirs) through pumping a fracturing fluid downhole. This operation is performed by using hydraulic fracturing pumps. The pistons of these pumps are mechanical components performing the intake and compressing fracture fluid by reciprocating action. During this alternati
Matéria (Rio J.). Publicado em: 19/07/2018
-
6. Fatigue strength of several dental ceramics indicated for CAD-CAM monolithic restorations
Abstract This in vitro study evaluated the fatigue strength of different ceramic materials indicated for monolithic restorations. Disc-shaped specimens were made according to ISO 6872 from five different ceramic materials: feldspathic ceramic (FC), polymer-infiltrated ceramic network (PIC), lithium disilicate glass-ceramic (LD), zirconia-reinforced lithium s
Braz. oral res.. Publicado em: 11/06/2018
-
7. HPGR simulation from piston-die tests with an itabirite ore
Abstract The Minas Rio project, owned by Anglo American, has HPGRs in open circuit operated as a tertiary/quaternary crushing stage. Currently this type of equipment is designed from HPGR tests on laboratory scale and pilot scale tests. This paper presents a methodology for simulating HPGR from piston-die tests on laboratory scale and a mathematical model de
REM, Int. Eng. J.. Publicado em: 2017-03
-
8. Reliability, failure probability, and strength of resin-based materials for CAD/CAM restorations
ABSTRACT Objective: This study investigated the Weibull parameters and 5% fracture probability of direct, indirect composites, and CAD/CAM composites. Material and Methods: Discshaped (12 mm diameter x 1 mm thick) specimens were prepared for a direct composite [Z100 (ZO), 3M-ESPE], an indirect laboratory composite [Ceramage (CM), Shofu], and two CAD/CAM co
J. Appl. Oral Sci.. Publicado em: 2016-10
-
9. Experimentally Validated Combustion and Piston Fatigue Life Evaluation Procedures for the Bi-Fuel Engines, Using an Integral-Type Fatigue Criterion
Abstract A relatively complete procedure for high cycle fatigue life assessment of the engine components is outlined in the present paper. The piston is examined as a typical component of the engine. In this regard, combustion process and transient heat transfer simulations, determination of the instantaneous variations of the pressure and temperature in the
Lat. Am. j. solids struct.. Publicado em: 2016-06
-
10. Aerothermoelastic Analysis of Functionally Graded Plates Using Generalized Differential Quadrature Method
Abstract In the present paper, the aerothermoelastic behavior of Functionally Graded (FG) plates under supersonic airflow is investigated using Generalized Differential Quadrature Method (GDQM). The structural model is considered based on the classical plate theory and the von Karman strain-displacement relations are utilized to involve the nonlinear behavio
Lat. Am. j. solids struct.. Publicado em: 2016-04
-
11. Oxidative Stress Parameters, Related Trace Elements Levels and Proteomics in Soybean Seeds in Order to Get a Better Assessment of Their Quality
Antioxidant systems, Fe, Cu, Zn, Mn and Ni levels and proteomics in soybean seeds of different performance in field were assessed. These results were correlated with the in vitro tests required by regulatory organisms, and the actual behavior in field. Basal superoxide content, superoxide dismutase (SOD) activity (20-80 U mg-1 protein) and 2,2-diphenyl-1-pic
J. Braz. Chem. Soc.. Publicado em: 2015-10
-
12. Silorane- and high filled-based"low-shrinkage" resin composites: shrinkage, flexural strength and modulus
This study compared the volumetric shrinkage (VS), flexural strength (FS) and flexural modulus (FM) properties of the low-shrinkage resin composite Aelite LS (Bisco) to those of Filtek LS (3M ESPE) and two regular dimethacrylate-based resin composites, the microfilled Heliomolar (Ivoclar Vivadent) and the microhybrid Aelite Universal (Bisco). The composites
Braz. oral res.. Publicado em: 01/03/2013