Porous Substrates
Mostrando 1-12 de 30 artigos, teses e dissertações.
-
1. Gas permeability and compressive strength evaluation of porous Al2O3 supported membrane
Abstract The aim was to investigate the feasibility of using a device to characterize permeability in porous substrates with low gas flux. Al2O3 supports were prepared by dry pressing using 1 to 3 wt% of polyethylene glycol (PEG) as a pore-forming agent. The green body was partially sintered at 1300 ºC. CO2 gas was used to measure both the pressure loss and
Cerâmica. Publicado em: 2022
-
2. In vitro Evaluation of PHBV/PCL Blends for Bone Tissue Engineering
The objective of this study was to evaluate Vero cells in in vitro biocompatibility tests with pure PHBV and PCL and 75/25 and 50/50 blends developed for bone tissue bioengineering in dense or porous forms. The biomaterials were characterized morphologically by scanning electron microscopy, (SEM) stereoscopic imaging (SI), and micrometer measurement. Cellula
Mat. Res.. Publicado em: 25/11/2019
-
3. Imidazolium-based Ionic Liquids Impregnated in Silica and Alumina Supports for CO2 Capture
Ionic liquids (ILs) physical immobilization in solid materials is a key strategy for developing efficient and low cost CO2 capture processes. In this work, two porous commercial substrates with different characteristics (silica and alumina) were impregnated with ILs by physical wet method. Imidazolium based IL combined with [Br]- and [Tf2N]- anions were used
Mat. Res.. Publicado em: 11/11/2019
-
4. Microstructure and Properties of Duplex Ni-P-TiO2/Ni-P Nanocomposite Coatings
Duplex Ni-P-TiO2/Ni-P coatings were electrodeposited onto brass substrates. High phosphorus Ni-P coatings were plated as the inner layer to improve the corrosion resistance, while low phosphorus sol-enhanced Ni-P-TiO2 coatings were deposited on the top to strengthen the mechanical property. The microstructure, morphology, mechanical property and corrosion re
Mat. Res.. Publicado em: 13/06/2019
-
5. Potential of Pinus elliottii Engelm. needles as substrate conditioner for the production of “Fepagro C37 reck”Citrus rootstocks”
Resumo A produção de mudas de citros em ambiente protegido demanda grande quantidade de substrato, o qual deve apresentar características físicas e químicas adequadas. O uso de condicionadores ácidos, como acículas de Pinus, em mistura com substratos alcalinos, possibilita o cultivo de mudas com maior qualidade. O objetivo foi avaliar o desenvolvimen
Rev. Bras. Frutic.. Publicado em: 03/06/2019
-
6. Preparation of Antireflective Silica Coating by the Sol-Gel Method for Heliothermic Power Plants
This work deals with the deposition of a thin layer of porous silica antireflective coating onto glass substrates. The films were deposited with different withdrawal speeds and heat-treated at 425°C for 30 minutes. The effects of heat treatment and film deposition rate on the films reflectance were evaluated. The diffuse reflectance was measured using ultra
Mat. Res.. Publicado em: 16/04/2018
-
7. Washing treatment impact on print quality of screen printed knitted fabrics
ABSTRACT The surface of textile materials is highly textured, commonly in non-uniform ways. Because of this texture effect, textile surface appears rougher and more porous than other printing substrates, which can cause excessive ink penetration during printing process. Next, washing process is very important factor because it influences ink characteristics
Matéria (Rio J.). Publicado em: 2016-09
-
8. 3D nanocomposite chitosan/bioactive glass scaffolds obtained using two different routes: an evaluation of the porous structure and mechanical properties
Porous synthetic substrates are developed through tissue engineering technologies to grow new tissue, restoring the function of tissue or an organ. For bone regeneration, these scaffolds must support the dynamic load exerted on this tissue, achieved primarily by increasing their compression strength, as established in the literature. The aim of this paper wa
Quím. Nova. Publicado em: 2016-05
-
9. Boron Doped Ultrananocrystalline Diamond Films on Porous Silicon: Morphological, Structural and Electrochemical Characterizations
Boron doped ultrananocrystalline diamond (BDUND) films were grown and characterized on porous silicon (PS) substrates. PS samples were prepared from n-type monocrystalline silicon wafers (100) with 1-20 Ω.cm of resistivity, by electrochemical etching, using HF-acetonitrile solution as electrolyte. BDUND films were grown by Hot Filament Chemical Vapor Deposi
Mat. Res.. Publicado em: 24/11/2015
-
10. Current developments of mixed conducting membranes on porous substrates
The fabrication of mixed ionic-electronic conducting (MIEC) ceramic-based membranes for oxygen separation has extensively increased in the last three decades as a promising alternative of clean energy delivery. In recent years, the interest on supported MIEC membranes has increased due to their attractive properties such as higher mechanical strength and oxy
Mat. Res.. Publicado em: 22/10/2013
-
11. Structural and fluid dynamic characterization of calcium carbonate-based porous ceramics
The aim of this work was to experimentally evaluate the use of calcium carbonate as a pore-generating agent in ceramic compositions. Compositions that contained 50% kaolin, 20% limestone, and different concentrations of quartz and feldspar were prepared by uniaxial pressing. Samples were heat-treated at a heating rate appropriate to induce calcium carbonate
Mat. Res.. Publicado em: 10/09/2013
-
12. Effect of implant design and bone density in primary stability
AIM: To evaluate the influence of the format and surface treatment of implants, as well as the substrate used in primary stability. METHODS: Thirty-two Conexão® implants were used: 8 conical (CC) (11.5 x 3.5 mm) and 24 cylindrical (11.5 x 3.75 mm) - 8 external hexagon implants without surface treatment (MS), 8 external hexagon implants with double Porous t
Braz. J. Oral Sci.. Publicado em: 2013-09