Pressure Flow Technique
Mostrando 1-12 de 174 artigos, teses e dissertações.
-
1. A Simplest Method to Enhance the Benefits of Internal Thoracic Artery Distal Occlusion
Abstract A common element of internal thoracic artery harvesting techniques is a distal vascular clamp placement at the end of the procedure, not only to avoid bleeding, but also to increase the internal hydrostatic pressure, diameter and flow. The logic indicates that the placement of this clamp at the beginning of the dissection will allow the artery to be
Braz. J. Cardiovasc. Surg.. Publicado em: 2021-06
-
2. Efeitos agudos da hiperinsuflação com o ventilador com aumento do tempo inspiratório sobre a mecânica respiratória: ensaio clínico cruzado randomizado
RESUMO Objetivo: Avaliar os efeitos da hiperinsuflação com o ventilador sobre a mecânica respiratória. Métodos: Foi realizado ensaio clínico cruzado randomizado com 38 pacientes ventilados mecanicamente com infecção pulmonar. A ordem da hiperinsuflação ou controle (sem alterações nos parâmetros) foi randomizada. A hiperinsuflação foi realiza
Rev. bras. ter. intensiva. Publicado em: 14/10/2019
-
3. Lower Limb Reconstruction - Fasciocutaneous Sural Flap
Resumo Objetivo Avaliar o uso do retalho fasciocutâneo sural de fluxo reverso na cobertura de lesões no terço distal dos membros inferiores. Métodos Foram analisados 24 casos, 20 de origem traumática, três por lesões esportivas e um por ressecção de lesão tumoral. Resultados Dos 24 prontuários avaliados, 16 eram homens e oito mulheres. A ida
Rev. bras. ortop.. Publicado em: 03/06/2019
-
4. Influence of water in the MQL technique in the grinding of steel AISI 4340 using CBN wheels
Abstract Usually, machining employs cooling methods to avoid high temperatures. In most cases, the cutting fluid is applied with high flow and low pressures. This technique consumes a large amount of cutting fluid that causes serious problems in the environment and in the health of the worker. An alternative to the conventional cooling method is the Minimum
REM, Int. Eng. J.. Publicado em: 2018-07
-
5. Evaluation of the oil flow using the MQL technique applied in the cylindrical plunge grinding of AISI 4340 steel with cbn grinding wheel
Abstract The grinding process is defined as an abrasive cutting action of a tool known as grinding wheel, which is submitted to high rotations, promoting excellent finishing and accuracy in dimensions, respecting the parameters established in each project. During the machining, the cutting edges of the abrasive grains undergo wearing and this increases the c
REM, Int. Eng. J.. Publicado em: 2018-07
-
6. COMPUTATIONAL FLUID DYNAMICS (CFD) APPLICATION FOR VENTILATION STUDIES IN BROILER HOUSES
ABSTRACT With the recent increase in the number of acclimatized broiler houses in Brazil, design and adaptation of facilities to withstand the tropical weather conditions enabling the maintenance of ideal conditions without increasing costs have been major challenges. The aim of this study was to evaluate the ventilation system in solid-wall broiler houses u
Eng. Agríc.. Publicado em: 2017-02
-
7. CHARACTERIZATION AND EVALUATION OF WAXY CRUDE OIL FLOW
Abstract Part of the oil found in the Brazilian subsoil has a high wax content, which makes its flow process difficult at low temperatures because of the increase in the viscosity of the fluid. This paper studied the flow behavior of waxy crude oil under variation in the temperature of the external environment of the flow, the volumetric flow rate of the oil
Braz. J. Chem. Eng.. Publicado em: 2016-12
-
8. Gas permeability of bentonite barriers: development, construction and testing of a measurement system
Abstract This article proposes a testing device to quickly and reliably estimate the gas permeability of bentonite-based clay barriers used in landfill cover systems. The testing methodology is based on a transient gas flow regime that passes through the barrier, therefore not requiring the use of sophisticated equipment that aim to maintain constant differe
REM, Int. Eng. J.. Publicado em: 2016-12
-
9. Experimental Investigation on Limit Cycle Wing Rock Effect on Wing Body Configuration Induced by Forebody Vortices
ABSTRACT The purpose of this paper is to present the aerodynamic and flow characteristics of a slender body with a 30° swept wing configuration undergoing a limit cycle oscillation using a synchronous measurement and control technique of wing rock/particle image velocimetry/dynamic pressure associated with the time history of the wing rock motion. The exper
J. Aerosp. Technol. Manag.. Publicado em: 2016-09
-
10. Electrochemical Behavior of Titanium Nitride Thin Films Deposited on Silicon by Plasma Discharge Technique in Cathodic Cage
Titanium nitride films were deposited on silicon by plasma discharge in cathodic cage with holes and without holes on the sides. Each film was deposited with a pressure of 253 Pa, treatment time of 2 h, and at diverse conditions of temperature and gas flow of N2 and H2. The electrochemical polarization and electrochemical impedance techniques were used to un
Mat. Res.. Publicado em: 22/08/2016
-
11. Pressurized Flow Solubilization System Using Electromagnetic Induction Heating Technique for Simultaneous Determination of Inorganic Elements (Ba, Ca, Cd, Cu, Fe, Mg, Mn, Na, Pb, Sr, Zn) in Sonicate Slurries of Biological Materials by Microwave Induced Plasma Optical Emission Spectrometry (MIP-OES)
A pressurized continuous flow system using electromagnetic induction heating technique has been developed for the determination of trace and minor element content in biological samples by microwave induced plasma-optical emission spectrometry (MIP-OES). The system allows the continuous solubilization of samples at an optimized temperature of 120 °C and pres
J. Braz. Chem. Soc.. Publicado em: 2016-03
-
12. Catalizadores de cobre soportado parareducción selectiva de glicerol
ABSTRACTThe biodiesel industry has brought with it an oversupply of glycerol, which is the byproduct of the process, generating a fall in its price. The transformation of glycerol into value-added compounds interest as it would improve the overall economic balance of biofuel production enabling environmentally sustainable development by using renewable raw m
Matéria (Rio J.). Publicado em: 2015-09