Riser
Mostrando 1-12 de 78 artigos, teses e dissertações.
-
1. The dispersion curve applied in guided wave propagation in prismatic rods.
Abstract The early detection of failures in structures is a subject of great interest in engineering; several of these techniques are linked with the elastic wave propagation, using guided waves is one of these alternatives. Several structures of interest in engineering are laminar arrangements; the wave propagation in this type of structures depends not on
Lat. Am. j. solids struct.. Publicado em: 02/07/2018
-
2. Hydrodynamics of an external-loop airlift reactor with inserted membrane
Abstract The objective of this study was to investigate the hydrodynamics of an external-loop airlift membrane reactor (ELAMR). The ELAMR was operated in two modes: without (mode A) and with bubbles in the downcomer (mode B), depending on the liquid level in the gas separator. The influence of the gas distributor’s geometry and various alcohol solutions on
Braz. J. Chem. Eng.. Publicado em: 2017-04
-
3. INFLUENCE OF THE MODEL SCALE ON HYDRODYNAMIC SCALING IN CFB BOILERS
Abstract The paper presents the results of experimental verification of the simplified set of scaling parameters for which the particle density as well as the cold model length scale may be chosen independently. The tests were carried out on two large scale 1/10 and 1/20 geometrically similar cold models of the Lagisza 966 MWth supercritical CFB boiler. The
Braz. J. Chem. Eng.. Publicado em: 2016-12
-
4. STUDY OF FEEDSTOCK INJECTION TO IMPROVE CATALYST HOMOGENIZATION IN THE RISER OF A FCC
Abstract A three dimensional gas-solid reactive flow model based on the Eulerian-Eulerian approach was used to study the effects of different nozzle designs with internal parts inside the FCC riser. The simulations were solved using Computational Fluid Dynamics (CFD) with CFX version 14.0 as tool. The results showed that the nozzle designs have a significant
Braz. J. Chem. Eng.. Publicado em: 2016-09
-
5. SOLID HOLDUP AND CIRCULATION RATE IN A LIQUID-SOLID CIRCULATING FLUIDIZED BED WITH VISCOUS LIQUID MEDIUM
Abstract Experiments were conducted in a liquid-solid circulating fluidized bed with different viscous liquids and particles to study the hydrodynamics, average solid hold up and solid circulation rate. The effects of operating parameters, i.e., primary liquid flow rate in the riser, auxiliary liquid flow rate, total liquid flow rate and viscosity of the liq
Braz. J. Chem. Eng.. Publicado em: 2015-12
-
6. Concreto nanoligado a base de sílica fundida para aplicação no riser de unidade de craqueamento catalítico fluido
O agregado de sílica fundida é uma matéria-prima que se mostra adequada para o desenvolvimento de concretos para aplicação em riser de unidade de craqueamento catalítico fluido de petróleo (UFCC). A sua baixa densidade aparente e reduzida condutividade térmica contribuem, respectivamente, para a diminuição do peso da estrutura refratária e maior e
Cerâmica. Publicado em: 2015-03
-
7. Avaliação metalúrgica da soldagem de revestimento inox austenítico sobre aço SAE 4130
O objetivo deste trabalho foi realizar uma avaliação metalúrgica da soldagem de revestimento inox austenítico sobre a área de selagem de tubos de Riser fabricados em aço SAE 4130. O estudo foi dividido em duas etapas. A primeira etapa teve como objetivo a determinação da taxa de diluição e taxa de deposição para os níveis máximo e mínimo de en
Soldag. insp.. Publicado em: 2014-12
-
8. Estudo da contribuição da transição de fase α-β do quartzo para o dano por ciclo térmico em um refratário empregado em UFCC
A deterioração de refratários utilizados em unidades fluidizadas de craqueamento catalítico (UFCC) é responsável por altos custos de manutenção para a indústria petroquímica. Esse fenômeno é comumente associado à deposição de coque durante a produção de hidrocarbonetos. Entretanto, outros mecanismos causadores de dano podem ocorrer, como a g
Cerâmica. Publicado em: 2014-09
-
9. An analysis of parametric instability of risers
In this work, three catenary riser models subjected to harmonic oscillations are studied. Two are finite-element models, one studied with Orcaflex, an offshore marine system analysis software, and another one with Abaqus, a generalist structural analysis software. The third model is an analytical reduced-order model that represents only the touch-down zone.
Lat. Am. j. solids struct.. Publicado em: 2014-05
-
10. Metodologia para aplicar LES ao craqueamento catalítico fluido em um reator riser industrial / Large eddy simulation application methodology to a fluid catalytic cracking industry reactor
The main objective of this thesis is to propose a methodology in how to apply Large Eddy Simulation (LES) on a unit of catalytic cracking. In order to achieve this, it was proposed an alternative way of constructing the computational mesh, by using quasi-uniform meshes. The proposed meshes were implemented to minimize the computational effort and procedure f
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 14/09/2012
-
11. Simulação de um alimentador Venturi em trecho ascendente no transporte pneumático de sólidos
The radial and axial distributions of coarse solids when fed directly in a riser are unknown, despite this type of feeding is very important for drying and preheating of solids during conveying. In this context, this thesis focused on studying the diluted conveying of coarse solids in a riser that was fed by a Venturi feeder in vertical orientation. Experime
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 30/08/2012
-
12. Análise da dinâmica dos movimentos de um riser híbrido auto-sustentável (RHAS) / Analysis of the dynamic motion of a self-standing hybrid riser
Descobertas recentes de petróleo em laminas d água cada vez mais profundas tem motivado o desenvolvimento de novas configurações de sistemas de produção de petróleo. Neste contexto, o Riser Hibrido Auto Sustentável (RHAS) surge como uma alternativa para produção de petróleo em águas ultraprofundas...Observação: O resumo, na íntegra, poderá se
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 29/06/2012