Screw Resistance
Mostrando 1-12 de 47 artigos, teses e dissertações.
-
1. Biomechanical Test after Hip Cannulated Screw Removal (in vitro Analysis)
Resumo Objetivo Avaliar, pormeio de ensaio biomecânico, a resistência e a energia necessária para ocorrência de fratura do fêmur proximal em osso sintético após retirada de parafusos canulados em forma de triângulo invertido e comparar os resultados obtidos com técnica de reforço utilizando polimetilmetacrilato (PMMA). Métodos Foramutilizados
Rev. bras. ortop.. Publicado em: 07/10/2019
-
2. Stabilization effect of kraft lignin into PBAT:Thermal analyses approach
ABSTRACT Sterically hindered phenols are an important class of synthetic antioxidants for polymers, commonly incorporated to inhibit polyolefins or polyesters oxidation. However, synthetic antioxidants use is under restricted regulation due to their potential health risk and environmental impacts. Thus, great interest has been attracted to the phenol-based n
Matéria (Rio J.). Publicado em: 16/09/2019
-
3. Influência do envelhecimento termo-oxidativo nas propriedades mecânicas e de amarelamento de blendas de poliestireno com borracha reciclada de estireno-butadieno (SBR)
RESUMO Este trabalho teve como objetivo avaliar o envelhecimento termo-oxidativo, nas propriedades mecânicas e de índice de amarelamento (YI), de blendas de poliestireno com borracha reciclada (SBRr), compatibilizadas. As blendas foram preparadas, inicialmente, em uma extrusora de rosca dupla corrotacional e, posteriormente, os grânulos extrudados foram m
Matéria (Rio J.). Publicado em: 16/09/2019
-
4. Effect of Particle Size on Bamboo Particle Board Properties
ABSTRACT In this work, bamboo chips (Dendrocalamus asper) were crushed according to four particle size classes (A = -35+40 mesh; B = -40+48 mesh; C = -48+60 mesh; D = -60+65 mesh) to produce particleboards with four different compositions (100%A; 75%A + 25% B; 50%A + 50%B; 25%A + 25%B + 25%C + 25%D). Each composition was considered a treatment. The aim was
Floresta Ambient.. Publicado em: 04/04/2019
-
5. INFLUENCE OF DIAMETER AND GEOMETRY IN THE TAPPING OF THE PILOT HOLE IN PEDICLE SCREWS
RESUMO Objetivo: Avaliar o torque de inserção e a força de arrancamento de cada parafuso com diferentes diâmetros e machos. Métodos: Foram utilizados no estudo blocos de poliuterano com orifício piloto de 2,7mm, sendo feito um grupo experimentais com 5 blocos sendo avaliado o torque de inserção com torquímetro e avaliado o arrancamento de cada par
Coluna/Columna. Publicado em: 2019-03
-
6. Diseño, simulación y análisis del proceso de extrusión de un perfil termoplástico en PVC rígido para optimizar el diseño de la matriz y los parámetros
ABSTRACT The objective of the present work was to verify and optimize the die design to manufacture a thermoplastic profile in rigid PVC using the simulation of the flow in the mentioned matrix through the use of Computational Fluid Dynamics (CFD) and through tests in extrusion, using an experimental calibrator, the required geometry and dimensions were obta
Matéria (Rio J.). Publicado em: 19/07/2018
-
7. Toughening of polystyrene using styrene-butadiene rubber (SBRr) waste from the shoe industry
Abstract The vulcanized rubber waste from the shoe industry causes environmental damage when it is incinerated or inappropriately discarded, turning this into a problem of major concern. Therefore, this study had as the main objective the Polystyrene (PS) toughening using different contents of white vulcanized styrene-butadiene rubber (SBRr) waste produced i
REM, Int. Eng. J.. Publicado em: 2018-04
-
8. Correlation between Processing, Morphology and Impact Resistance of PBT/ABS Blends
To understand the processing influence in an intermeshing corotating twin-screw extrusion (ICTSE) on the morphology and impact properties of the uncompatibilized PBT/ABS (70/30) blend, it was submitted to different processing parameters. In this way both morphology and impact properties (resistance and ductile brittle transition temperature (DBTT) would be a
Mat. Res.. Publicado em: 30/10/2017
-
9. Curaua fiber reinforced high-density polyethylene composites: effect of impact modifier and fiber loading
Abstract Short fibers are used in thermoplastic composites to increase their tensile and flexural resistance; however, it often decreases impact resistance. Composites with short vegetal fibers are not an exception to this behavior. The purpose of this work is to produce a vegetal fiber reinforced composite with improved tensile and impact resistance in rela
Polímeros. Publicado em: 07/06/2016
-
10. Influence of Sealing of the Screw Access Hole on the Fracture Resistance of Implant-Supported Restorations
Resumo O objetivo deste estudo foi avaliar a influência do selamento do orifício de acesso ao parafuso (OAP) na resistência à fratura de coroas metalocerâmicas implantossuportadas aparafusadas. Pilares UCLA foram utilizados para fazer 30 molares inferiores implantossuportados e divididos igualmente em três grupos: Grupo AS: coroas aparafusadas com o OA
Braz. Dent. J.. Publicado em: 2016-04
-
11. Influence of implant-abutment angulations and crown material on stress distribution on central incisor: a 3D FEA
Abstract Aim: To investigate the effect of implant-abutment angulation and crown material on stress distribution of central incisors. Finite element method was used to simulate the clinical situation of a maxillary right central incisor restored by two different implant-abutment angulations, 15° and 25°, using two different crown materials (IPS E-Max CAD
Braz. J. Oral Sci.. Publicado em: 2015-12
-
12. Influence of the Addition of Montmorillonite in an Epoxy Powder Coating Applied on Carbon Steel
AbstractPolymer coatings have been used for the corrosion protection of metal surfaces acting as a physical barrier against several corroding media. In spite of the good efficiency of these coatings their resistance is limited due to the presence of localized defects which give place to localized corrosion. Aiming to improve the barrier properties of these c
Mat. Res.. Publicado em: 2015-10