Shear Forces
Mostrando 1-12 de 125 artigos, teses e dissertações.
-
1. Some Aspects of Numerical Modeling of Steel-Concrete Composite Beams with Prestressed Tendons
Abstract Aspects about the numerical modeling of three-dimensional prestressed steel-concrete composite beams by using the finite element (FE) method are highlighted and commented in this work. Emphasis is given to the numerical treatment of bonded and unbonded tendons. The proposed modeling technique uses curved beam and catenary elements for simulating int
Lat. Am. j. solids struct.. Publicado em: 15/08/2019
-
2. Toughness in Santa Inês lamb meat has negative impact on consumer evaluation
RESUMO A maciez da carne é um atributo importante para os consumidores do mundo todo. Porém, ainda faltam estudos sobre sua importância na área de carne de cordeiro para consumidores brasileiros. O objetivo do estudo foi verificar a avaliação dos consumidores em relação à carne de cordeiro com força de cisalhamento elevada. Oito cordeiros foram aba
Rev. bras. saúde prod. anim.. Publicado em: 29/07/2019
-
3. Hankel transformation method for solving the Westergaard problem for point, line and distributed loads on elastic half-space
Abstract The Hankel transformation method was used in this work to determine the normal and shear stress distributions due to point, line and distributed loads applied to the surface of an elastic media. The elastic media considered in this study was assumed to be inextensible in the horizontal directions, and the only non-vanishing displacement component is
Lat. Am. j. solids struct.. Publicado em: 04/02/2019
-
4. Single variable new first-order shear deformation theory for isotropic plates
Abstract This paper presents a single variable new first-order shear deformation plate theory with only one fourth-order partial governing differential equation. It may be noted that, first-order shear deformation plate theory of Mindlin has three coupled partial governing differential equations involving three unknown functions. Even a recently developed ne
Lat. Am. j. solids struct.. Publicado em: 11/10/2018
-
5. What are the advantages of living in a community? A microbial biofilm perspective!
Biofilm formation is the preferred mode of growth lifestyle for many microorganisms, including bacterial and fungal human pathogens. Biofilm is a strong and dynamic structure that confers a broad range of advantages to its members, such as adhesion/cohesion capabilities, mechanical properties, nutritional sources, metabolite exchange platform, cellular commu
Mem. Inst. Oswaldo Cruz. Publicado em: 26/07/2018
-
6. Amorphization of Graphite Flakes in Gray Cast Iron Under Tribological Load
A gray cast iron disc, which had been submitted to a heavy duty automotive brake test, was examined with energy filtered transmission electron microscopy. A graphite flake in a convenient angular position showed the shear interaction of graphite layers with the iron matrix in nano-scale resolution. Atomic layers of graphite were wedged into the ferritic bulk
Mat. Res.. Publicado em: 28/05/2018
-
7. Rheological Parameters as Affected by Water Tension in Subtropical Soils
ABSTRACT Rheological parameters have been used to study the interaction between particles and the structural strength of soils subjected to mechanical stresses, in which soil composition and water content most strongly affect soil resistance to deformation. Our objective was to evaluate the effect of water tension on rheological parameters of soils with diff
Rev. Bras. Ciênc. Solo. Publicado em: 23/06/2016
-
8. Analysis and Design of Reinforced Concrete Deep Beams by a Manual Approach of Stringer-Panel Method
Abstract D-regions are defined by its non-linear strain distribution over a cross section. Deep beams are an example of D-regions, as most of its load is usually directly delivered to supports by arch mechanism. The present paper focus on the Stringer-Panel Method (SPM), an alternative procedure to some well-known methods for designing this type of structure
Lat. Am. j. solids struct.. Publicado em: 2016-06
-
9. High Order Impact Elastic Analysis of Circular Thick Cylindrical Sandwich Panels Subjected to Multi-mass Impacts
Abstract This study dealt with the dynamic model of composite cylindrical sandwich panels with flexible cores and simply supported boundary conditions under low velocity impacts of multiple large or small masses using a new improved higher order sandwich panel theory (IHSAPT). In-plane stresses were considered for the core and face sheets. Formulation was ba
Lat. Am. j. solids struct.. Publicado em: 2015-12
-
10. Effect of bonding protocol on shear bond strength of orthodontic brackets: An in vitro study
The aim of this study was to evaluate the shear bond strength of bracket composites as a function of the application of flow adhesive prior to the composite and light curing time.Material and methods:Freshly extracted bovine permanent central incisors (50) were acid etched and divided into four groups varying the attachment protocol: (1) no adhesive, composi
Matéria (Rio J.). Publicado em: 2014-09
-
11. 3D finite element modeling of grains refinement for magnesium alloys by extrusion-shear and experimental verification
To explore the deformation mechanisms of a new composite extrusion including extrusion and successive shear subsequently which is shorten "ES", Three dimensional finite element modeling of grain refinements for magnesium alloys by ES process has been researched. The ES die have been designed and manufactured and installed to the horizontal extruder. Finite e
Mat. Res.. Publicado em: 28/07/2014
-
12. Effect of relative humidity on creep-shrinkage behaviour of composite tall buildings
Relative humidity of environment affects creep and shrinkage behaviour of a concrete member of composite tall buildings. These buildings are more prone to redistribution of forces as adjacent steel columns and RCC shear walls have quite different characteristics. In this paper, study is carried out to evaluate the effect of relative humidity of environment f
Lat. Am. j. solids struct.. Publicado em: 2013-05