Single Phase Flow
Mostrando 1-12 de 98 artigos, teses e dissertações.
-
1. Experimental study on the self-suspending proppant-laden flow in a single fracture
Abstract The flow of proppant-laden fluid (PLF) in the fracture is a typical problem of solid-liquid two phase flow, and the transportation and deposition of proppants are essential to determine the flow conductivity of hydraulic fracturing. The self-suspending proppant with a water soluble surface coating is a newly presented supporting material and has gre
REM, Int. Eng. J.. Publicado em: 2018-04
-
2. Experimental study of the diffusion-controlled corrosion of copper in the bottom of a jet stirred reactor
Abstract Jet stirred tank reactors are usually preferred to mechanically stirred tank reactors in the case of high pressure stirred tank reactors in order to avoid the mechanical problems inherent with mechanically agitated reactors. Owing to the impact force exercised by the fluid jet on the tank bottom, the tank bottom is subjected to severe corrosion. The
Braz. J. Chem. Eng.. Publicado em: 2018-01
-
3. Numerical Study of Wake Characteristics in a Horizontal-Axis Hydrokinetic Turbine
ABSTRACT Over the years most studies on wake characteristics have been devoted to wind turbines, while few works are related to hydrokinetic turbines. Among studies applied to rivers, depth and width are important parameters for a suitable design. In this work, a numerical study of the wake in a horizontal-axis hydrokinetic turbine is performed, where the ma
An. Acad. Bras. Ciênc.. Publicado em: 01/12/2016
-
4. SELF-SIMILARITY OF VERTICAL BUBBLY JETS
AbstractAn integral model for vertical bubbly jets with nearly monodisperse bubble sizes is presented. The model is based on the Gaussian type self-similarity of mean liquid velocity, bubble velocity and void fraction, as well as on functional relationships for initial liquid jet velocity and radius, bubble diameter and relative velocity. Adjusting the model
Braz. J. Chem. Eng.. Publicado em: 2015-06
-
5. CFD and experimental investigation on the heat transfer characteristics of alumina nanofluids under the laminar flow regime
This study reports experimental and Computational Fluid Dynamics (CFD) investigations of the laminar convective heat transfer coefficient of Al2O3/water nanofluids in a circular tube under uniform and constant heat flux on the wall. Three different models including a constant physical properties single-phase (CP-SP) model, a variable physical properties sing
Braz. J. Chem. Eng.. Publicado em: 2014-06
-
6. NUMERICAL ANALYSIS OF THE FLOW OF EMULSION THROUGH STRAIGHT AND CONSTRICTED CAPILLARIES / ANÁLISE NUMÉRICA DO ESCOAMENTO DE EMULSÕES ATRAVÉS DE CAPILARES RETOS E CAPILARES COM GARGANTA
Emulsion can be used as a mobility control agent in enhanced oil recovery methods in order to achieve a more efficient sweep of the reservoir. The application of such technique requires full understanding of how emulsions flow in a porous material. The macroscopic flow behavior can be determined based on the pore scale flow, at which emulsions cannot be trea
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 15/09/2011
-
7. Análise do modelo de mistura aplicado em escoamentos isotérmicos gás-líquido / Analysis of mixture model applied in gas-liquid isothermals flows
Gas-liquid flows are often found in nature as well as in various industrial applications. In the oil production, for example, in natural or artificial lift systems (continuous or intermittent gas-lift), gas and oil flow simultaneously in pipes. The prediction of gas-liquid behavior becomes necessary for technical and economic viability of many industrial pro
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 13/07/2011
-
8. Mathematical Modeling of the Ester Oil-Refrigerant R134a Mixture Two-Phase Flow with Foam Formation Through a Small Diameter Tube
This work presents a mathematical modeling to study the ester oil ISO VG-10-refrigerant R134a mixture two-phase flow with foam formation through a 3.22 mm ID tube. Based on experimental visualization results, the flow is divided into three regions: a single phase flow at the inlet of the tube; an intermediary bubbly flow region; and a foam flow region at the
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2011-09
-
9. A new correlation for single and two-phase flow pressure drop in round tubes with twisted-tape inserts
Twisted-tape inserts are frequently used in heat exchangers as a passive and inexpensive heat transfer enhancement method. However, their use results not only heat transfer coefficient increments, but also pressure drop penalties. The present study analyses the literature on single and two-phase frictional pressure drop inside tubes with twisted-tape inserts
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2011
-
10. Comparison between experimental data and numerical modeling for the natural circulation phenomenon
The study of natural circulation phenomenon has been object of crescent interest in scientific community in recent years. The new generation of compact nuclear reactors uses natural circulation of the fluid as a residual heat removal cooling system in case of accident or shutdown. The objective of this paper is to present a comparison between experimental da
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2011
-
11. Simulação do escoamento monofásico em um estágio de uma bomba centrífuga utilizando técnicas de fluidodinâmica computacional
Oil production and exploration techniques have evolved in the last decades in order to increase fluid flows and optimize how the required equipment are used. The base functioning of Electric Submersible Pumping (ESP) lift method is the use of an electric downhole motor to move a centrifugal pump and transport the fluids to the surface. The Electric Submersib
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 17/12/2010
-
12. Avaliação dos tipos de processamento na descontaminação e na degradação do polipropileno reciclado / Evaluation of types of processing in the decontamination and degradation of recycled polypropylene
Polypropylene is one of the most used polymers worldwide, especially by the disposable packaging industry, causing serious environmental problems. Despite the fact that recycling this polymer has become common in Brazil due to its growing market, there are still some restrictions regarding its use in direct-contact food packaging. Therefore, in order to eval
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 15/12/2010