Steel Pipes
Mostrando 1-12 de 43 artigos, teses e dissertações.
-
1. Characterization of Austenite Decomposition in Steels with Different Chemical Concepts and High Potential to Manufacture Seamed Pipes for Oil and Gas Industry
This work presents the characterization of austenite decomposition kinetics in two steels during continuous cooling considering non-deformed austenite grains. Two different chemical concepts of steels were evaluated: low carbon - high manganese and a relatively new concept based on low carbon - low manganese - high niobium contents. Dilatometric experiments,
Mat. Res.. Publicado em: 21/10/2019
-
2. Keyhole GTAW with Dynamic Wire Feeding Applied to Orbital Welding of 304L SS Pipes
Resumo Atualmente, no cenário brasileiro de óleo e gás a execução dos processos de soldagem para aços inoxidáveis consiste em sua grande maioria de aplicações manuais, dificultando qualquer aumento de produtividade e repetibilidade dos processos. Portanto, a automação desta etapa permite grandes avanços com resultados mais confiáveis, menores c
Soldag. insp.. Publicado em: 15/08/2019
-
3. Quality analysis of galvanized pipes applied to natural gas installations in civil construction
ABSTRACT Some natural gas distributors for residential and commercial buildings in Brazil use galvanized steel tubes and fittings manufactured by the hot-dip zinc process that are supported by the specifications contained in the Brazilian Standards. Zinc coating is one of the most widely used methods to provide protection against corrosion. It is therefore e
Matéria (Rio J.). Publicado em: 10/06/2019
-
4. Effect of the Chemical Homogeneity of a Quenched and Tempered C-Mn Steel Pipe on the Mechanical Properties and Phase Transformations
Seamless steel pipes for application in the oil and gas industries are manufactured from quenched and tempered steel. Aiming to meet the required characteristics, it is necessary that the microstructure and the mechanical properties are homogeneous along the wall thickness of the pipes, which is even more critical for thick wall pipes. Considering the seamle
Mat. Res.. Publicado em: 03/06/2019
-
5. Tensile Armor Wires Submitted to Slow Strain Rate Tests in a Corrosive Environment and Cathodic Protection: a Comparison Between Two Different Microstructures
Tensile armor in flexible pipes consists of two or more layers of steel wires. Damage to the outer sheath may cause ingress of seawater in the annular space and thus corrosion of the armor wires. This work focused on the susceptibility of these wires to stress corrosion cracking (SCC) and hydrogen embrittlement (HE) using a slow strain rate test (SSRT) under
Mat. Res.. Publicado em: 06/05/2019
-
6. Characterization of Phase Transformations and Microstructural Changes in an API 5CT L80 Steel Grade During Ni Alloy Laser Cladding
The superficial coatings in micro-alloyed steel pipes has been a pointed way to decrease the corrosion problems in oil and gas industry. However, little emphasis has been given to the substrate. The effects of the deposition method on the steel microstructure and properties are still not well described. In this context, this work studied the effect of Ni sup
Mat. Res.. Publicado em: 26/07/2018
-
7. Influencia de la temperatura en ensayos de arrancamiento sobre diferentes sistemas epoxi-acero de uso en conectores de ductos flexibles
ABSTRACT In the offshore oil fields located in deep and ultra-deep waters they are used flexible pipes. In many cases inside these pipes, the hydrocarbons are transported at elevated temperatures. At the ends of the flexible pipes are installed end fittings, these are the connection with sea platforms and different subsea systems. In the assembly of end fitt
Matéria (Rio J.). Publicado em: 19/07/2018
-
8. Nondestructive Microstructural Characterization of Superduplex Stainless Steel by Double Loop Electrochemical Polarization Reactivation Portable Test
Superduplex stainless steels (SDSS) are frequently employed in the petrochemical industries where is required high mechanical strength, toughness, and corrosion resistance. However, these properties can be affected by deleterious phases formation due thermomechanical processes applied in the field during pipes and vessels construction. This work propose the
Mat. Res.. Publicado em: 23/10/2017
-
9. The use of Shearography technique to evaluate polymeric composite repairs - case study
ABSTRACT Pipelines are subject to a variety of defects such as wall thickness loss, grooves, dents and holes. To restore the pipe integrity, polymeric composite repairs can be used. The inspection of repaired pipes is of fundamental importance, not only to verify the initial integrity, but also to monitor their state over time. Shearography is a laser optica
Matéria (Rio J.). Publicado em: 09/10/2017
-
10. Effect of Ferrite on the Precipitation of σ Phase in Cast Austenitic Stainless Steel Used for Primary Coolant Pipes of Nuclear Power Plants
The effect of ferrite phase on the precipitation of σ phase in a Z3CN20.09M cast austenitic stainless steel (CASS) used for primary coolant pipes of pressurized water reactor (PWR) nuclear power plants was investigated by using isothermal heat-treatment, optical microscopy (OM), transmission electron microscopy (TEM) and electron probe microanalysis (EPMA)
Mat. Res.. Publicado em: 28/09/2017
-
11. Efecto de la Composición Química del Metal de Aporte y del Calor Aportado Sobre la Microestructura y las Propiedades Mecánicas de Juntas Soldadas de Aceros Inoxidables Dúplex
Abstract Duplex stainless steels are characterized by good weldability and mechanical properties; they also present a high resistance to general and localized corrosion. They are the main materials when welding pipes with high requirements in different industries, mainly oil and gas. These steels have a microstructure consisting of two phases: 50% austenite
Soldag. insp.. Publicado em: 2017-06
-
12. Evaluation of Microstructure and Mechanical Properties of Seamless Steel Pipes API 5L Type Obtained by Different Processes of Heat Treatments
This research presents the influence of manufacturing processes and heat treatments on the resulting microstructures and mechanical properties of an API 5L PSL2 seamless steel pipe. Three different conditions are considered - as rolled, normalized and quenched and tempered - to obtain the grades X42R, X42N and X70Q, respectively. Scanning electron microscopy
Mat. Res.. Publicado em: 06/03/2017