Tensile Test
Mostrando 1-12 de 331 artigos, teses e dissertações.
-
1. Adventitial Collagen Cross-Linking by Glutaraldehyde Reinforcing Human Saphenous Vein - Implication for Coronary Artery Bypass Grafting
ABSTRACT Introduction: A weak venous wall is one of the major reasons contributing to vein graft failure after coronary artery bypass grafting (CABG). We investigated whether adventitial collagen cross-linking by glutaraldehyde reinforces venous wall, preserving the endothelium of veins during high-pressure distention. Methods: Human saphenous veins (SVs)
Brazilian Journal of Cardiovascular Surgery. Publicado em: 2022
-
2. Caracterização Mecânica da Região Soldada de Tailor Welded Blanks (TWB) a Partir do Perfil de Microdureza
Resumo No Tailor Welded Blank (TWB) são soldadas chapas de especificações distintas, antes da conformação. Sua caracterização, na região soldada, por métodos convencionais de tração, pode ser dificultada pelo estreito comprimento da solda. Novas metodologias e alternativas são analisadas. Este trabalho visou caracterizar mecanicamente a região s
Soldag. insp.. Publicado em: 02/12/2019
-
3. Impacto nas Propriedades Mecânicas e Tensões Residuais do Material ASTM A572 Grau 50 Soldado por Arco Submerso com Alívio de Tensões Térmico
Resumo O aço ASTM A572 Grau 50 é utilizado na fabricação de conjuntos soldados para aerogeradores, por este motivo, a realização de alívio de tensões é de grande importância para correção dos impactos causados pelos processos de soldagem, bem como, o conhecimento das propriedades finais obtidas com a realização deste processo. O objetivo desse
Soldag. insp.. Publicado em: 02/12/2019
-
4. Avaliação do comportamento de estanqueidade à água de argamassas e hidrorrepelentes – Parte II
RESUMO Além da função estética, os revestimentos de fachada protegem as edificações da penetração de água e, consequentemente, diminuem a propensão ao surgimento de manifestações patológicas que levariam à degradação da superfície. Este trabalho apresenta os ensaios de avaliação do comportamento de estanqueidade à água de revestimentos a
Matéria (Rio J.). Publicado em: 25/11/2019
-
5. Bond strength evaluation between textiles reinforced mortar with carbon nanotubes and concrete substrate
Abstract The influence of using carbon nanotubes to improve bond strength between textiles reinforced mortar and concrete was investigated. Forty-two specimens were tested using double-shear test to evaluate the effect of various parameters such as CNTs addition, type of textile material, bond length and width, and number of TRM layers on the bond behavior.
Lat. Am. j. solids struct.. Publicado em: 25/11/2019
-
6. Bionanocomposites of PLA/PBAT/organophilic clay: preparation and characterization
Abstract The objective of this study was to develop bionanocomposites from blends of poly(lactic acid) (PLA) and poly(butylene adipate-co-terephthalate) (PBAT) and from 3% and 6% bentonite clay. Initially, the bentonite clay was treated with Praepagen salt, and the properties of the modified clay were evaluated. After the organophilization of the clay was co
Polímeros. Publicado em: 04/11/2019
-
7. Effect of grape seed extract-containing phosphoric acid formulations on bonding to enamel and dentin
Abstract The aim was to evaluate the effect of 2% grape seed extract (GSE) containing phosphoric acid (PhA) on the bond strength to enamel and dentin. The control group was 37% PhA. The following three PhA formulations with 2% GSE and 20% ethanol were obtained: GSE5 = 5% PhA; GSE10 = 10% PhA; and GSE20 = 20% PhA. The enamel and dentin surfaces of molars were
Braz. oral res.. Publicado em: 28/10/2019
-
8. Estudo comparativo entre agentes reticulantes para possível aplicação no tratamento do ceratocone
RESUMO Com o presente estudo, objetivou-se comparar a técnica padrão do CXL com o tratamento utilizando a genipina como reticulante, com e sem desepitelização da córnea. Comparou-se propriedades químicas, mecânicas e morfológicas de córneas de suínos submetidas aos tratamentos de crosslinking com riboflavina egenipina, bem como comparar a citotoxic
Matéria (Rio J.). Publicado em: 28/10/2019
-
9. Evaluation of the stiffening mechanism based on micro-sized particle inclusions in laminated composites
Rigid particles have been incorporated into laminated composites, especially to enhance their bending performance attributed to the stiffening of the matrix phase (i) and the increased interlaminar shear resistance (ii). In order to better evaluate the improvement mechanism provided by the particulate inclusions, this work investigates the incorporation of m
Mat. Res.. Publicado em: 17/10/2019
-
10. Effect of Ca Content on Properties of Extruded Mg-3Zn-0.5Sr-xCa Alloys for Medical Applications
Mg-3Zn-0.5Sr-xCa(wt.%) (x=0, 0.2, 0.5) alloys were fabricated by casting and hot extrusion. X-ray diffraction (XRD) and optical microscopy observation showed that the microstructure of Mg-3Zn-0.5Sr-xCa alloys was composed of α-Mg matrix and Mg17Sr2 phase precipitated along grain boundaries. The tensile strength of the alloy increased from 255MPa to 305MPa w
Mat. Res.. Publicado em: 30/09/2019
-
11. Study of the compressive and tensile strenghts of self-compacting concrete with sugarcane bagasse ash
Resumo Neste trabalho foram avaliadas as resistências à compressão axial aos 3, 7 e 28 dias de idade e a resistência à tração aos 28 dias de idade, de corpos de prova de duas composições de concreto autoadensável (CAA). A diferença entre ambas, era a presença da cinza do bagaço da cana-de-açúcar (CBC), na taxa de substituição de 10% da massa
Rev. IBRACON Estrut. Mater.. Publicado em: 23/09/2019
-
12. Tensile and fatigue properties, machinability and machined surface roughness of Al-Si-Cu alloys
ABSTRACT In this paper, the aim was to determine if ASC91 (9 % Al, 1 % Cu) could be replaced with ASC73 (7 % Al, 3 % Cu) aluminium alloy, with presumably improved machinability due to lower silicon content (9 to 7 %) and retained mechanical properties due to a higher copper content (1 to 3 %). The test samples were excised from cylinder heads produced by the
Matéria (Rio J.). Publicado em: 16/09/2019