Tribological
Mostrando 1-12 de 93 artigos, teses e dissertações.
-
1. Avaliação dos processos de fratura em filmes finos através da simulação de ensaios de indentação com penetradores esféricos
RESUMO Recentes trabalhos propõem a utilização dos ensaios de indentação como uma ferramenta capaz de avaliar características mecânicas de filmes finos, assim como avaliar possíveis falhas em sistemas que conjugam filmes de alta dureza depositados em substratos metálicos em solicitações tribológicas. Entretanto, a implementação da técnica de i
Matéria (Rio J.). Publicado em: 25/11/2019
-
2. Avaliação tribológica de óleos hidráulicos biodegradável e mineral com deslizamento entre as ligas de Cu-Zn e WC-CoCr
RESUMO A correta seleção dos óleos lubrificantes e das superfícies de contato melhoram o desempenho e reduzem o consumo de energia das máquinas Por isso, a engenharia de superfícies propõe novos revestimentos aos quais seu comportamento tribológico combinado com o uso de óleos biodegradáveis em componentes de sistema hidráulicos, não são conheci
Matéria (Rio J.). Publicado em: 25/11/2019
-
3. Influence of the Gas Pressure of Plasma Nitriding on the Structural, Mechanical and Tribological Surface Properties of AISI 316L
In this paper, the influence of gas nitriding (80% H2-20% N2) pressure (between 3 and 7 Torr) on the modification of surface properties of AISI 316L stainless steel is examined. The structural, mechanical, tribological and electrochemical properties of the layer produced in disk samples were studied. The samples’ characteristics were determined by scanning
Mat. Res.. Publicado em: 15/07/2019
-
4. Tribology of natural Poly-Ether-Ether-Ketone (PEEK) under transmission oil lubrication
Abstract High performance polymeric materials such as poly-ether-ether-ketone (PEEK) are increasingly being used for challenging tribological applications in order to replace metal parts in vehicle engines and transmissions. The tribology of natural PEEK, under oil-lubricated conditions, was studied for different metal counterbody finishes. Two different fin
Polímeros. Publicado em: 04/07/2019
-
5. Electrolytic polishing of compacted graphite iron for revealing subsurface graphite of honed cylinders
ABSTRACT The superficial characteristics of honed surfaces are relevant for the tribological performance of cylinders of internal combustion engines (MCI). Recent studies found a correlation between the occurrence of the phenomenon called folded metal and the presence of graphite of cast irons. However, the honing process tends to overlap the graphite, such
Matéria (Rio J.). Publicado em: 20/05/2019
-
6. Dependence of Wear and Mechanical Behavior of Nitrocarburized/CrN/DLC Layer on Film Thickness
Diamond-like carbon (DLC) films are amorphous metastable carbon form that provide interesting mechanical and tribological properties. The role of film thickness influence upon wear and mechanical properties is of interest and not yet fully reported. In this study, two samples of previously plasma nitrocarburized, quenched and tempered H13 steel were duplex t
Mat. Res.. Publicado em: 31/01/2019
-
7. Tribological behavior of hydrogenated W-C/a-C:H coatings deposited by three different sputtering techniques
Abstract The evolution of structure, mechanical properties and friction behavior of DC magnetron sputtered (DCMS), high power impulse magnetron sputtered (HiPIMS) and high target utilization sputtered (HiTUS) W-C:H coatings was investigated as a function of the addition of acetylene and hydrogen into Ar atmosphere. The gradual addition of reactive gases caus
Cerâmica. Publicado em: 2019-01
-
8. Influence of Cryogenic Treatment on the Tribological Behaviour of AISI H21 Tool Steel
The aim of the present work was to find out the optimum cryosoaking duration of deep cryogenic treatment to reduce the wear rate. The AISI H21 hot work tool steel specimens were hardened at 1195 ºC, cryotreated at -185 ºC for 6 to 30 h, double tempered at 540 ºC and soft tempered at 100 ºC. The hardness, impact toughness, wear rate and microstructural ch
Mat. Res.. Publicado em: 29/10/2018
-
9. Carbon based DLC films: Influence of the processing parameters on the structure and properties
ABSTRACT Hydrogenated carbon-based films, such as DLC (“Diamond Like Carbon”), have interesting properties such as excellent tribological behavior, low friction coefficient, high superficial hardness and good wear resistance; they are chemically inert and highly corrosion resistant. They are deposited by means of PACVD (plasma-assisted chemical vapor dep
Matéria (Rio J.). Publicado em: 19/07/2018
-
10. The influence of Nano-TiO2 and Nano-Al2O3 Particles in Silicate Based Electrolytes on Microstructure and Mechanical Properties of Micro Arc Coated Ti6Al4V Alloy
Ceramic oxide coatings were fabricated on Ti6Al4V alloy by micro arc oxidation (MAO) in silicate electrolytes, with nano-TiO2 and nano-Al2O3 and without nano-additives. Effects of nano additives on the structural and mechanical properties of the MAO coatings were analysed. The MAO coatings were investigated by scanning electron microscopy (SEM), Energy-Dispe
Mat. Res.. Publicado em: 18/06/2018
-
11. Amorphization of Graphite Flakes in Gray Cast Iron Under Tribological Load
A gray cast iron disc, which had been submitted to a heavy duty automotive brake test, was examined with energy filtered transmission electron microscopy. A graphite flake in a convenient angular position showed the shear interaction of graphite layers with the iron matrix in nano-scale resolution. Atomic layers of graphite were wedged into the ferritic bulk
Mat. Res.. Publicado em: 28/05/2018
-
12. Lubricated Conditions Imposed on Coating Multi-layer on Wear Resistance Under Cr2O3 Effect
Lubricated pin-on-disk sliding wear tests were performed on applied to Al-0.1Mg-0.35Ni-Si Alloy by using the spray coating method has been investigated. Different loads were 5, 10, and 15 N at a sliding velocity, 1.32 m/s at room temperature and 60% relative humidity. The surfaces were analyzed by using X-ray diffraction the residual (XRD), energy dispersive
Mat. Res.. Publicado em: 16/04/2018