Wear Mechanism
Mostrando 1-12 de 51 artigos, teses e dissertações.
-
1. Corrosion and Micro-abrasive Wear Behaviour of 2524-T3 Aluminium Alloy with PAni-NPs/PSS LbL Coating
In this paper, we present an alternative method to obtain thin films for coating protection on the surface of the AA2524-T3 Al-alloy by using the Layer-by-Layer (LbL) technique. The LbL films were fabricated by alternated immersion of the Al-alloy into a poly(styrene sulfonate) (PSS) and polyaniline nanoparticles (PAni-NPs) solutions, obtaining a PAni-NPs/PS
Mat. Res.. Publicado em: 06/06/2019
-
2. Carbon based DLC films: Influence of the processing parameters on the structure and properties
ABSTRACT Hydrogenated carbon-based films, such as DLC (“Diamond Like Carbon”), have interesting properties such as excellent tribological behavior, low friction coefficient, high superficial hardness and good wear resistance; they are chemically inert and highly corrosion resistant. They are deposited by means of PACVD (plasma-assisted chemical vapor dep
Matéria (Rio J.). Publicado em: 19/07/2018
-
3. Strontium ranelate inhibits wear particle-induced aseptic loosening in mice
The imbalance between bone formation and osteolysis plays a key role in the pathogenesis of aseptic loosening. Strontium ranelate (SR) can promote bone formation and inhibit osteolysis. The aim of this study was to explore the role and mechanism of SR in aseptic loosening induced by wear particles. Twenty wild-type (WT) female C57BL/6j mice and 20 sclerostin
Braz J Med Biol Res. Publicado em: 10/07/2018
-
4. Rheo-Squeeze Casting of High-Silicon Aluminium Alloy Pipes with Gradient Structures and Their Mechanical Properties
Three different compositions of high-Si Al alloy pipe, with a gradient structure, were produced through semi-solid rheological squeeze casting, the microstructural characteristics of which were investigated. The mechanism of gradient structure formation and the effect of acicular Fe-rich phases on liquid segregation were revealed. Meanwhile, the crystal stru
Mat. Res.. Publicado em: 11/06/2018
-
5. Lubricated Conditions Imposed on Coating Multi-layer on Wear Resistance Under Cr2O3 Effect
Lubricated pin-on-disk sliding wear tests were performed on applied to Al-0.1Mg-0.35Ni-Si Alloy by using the spray coating method has been investigated. Different loads were 5, 10, and 15 N at a sliding velocity, 1.32 m/s at room temperature and 60% relative humidity. The surfaces were analyzed by using X-ray diffraction the residual (XRD), energy dispersive
Mat. Res.. Publicado em: 16/04/2018
-
6. [RETRACTED ARTICLE]: Load Dependent Wear Analysis of Manganese Steels - Influence of Al Content
In this paper influence of load on change in weight loss (mg), hardness and wear transition of 0.12 wt.% Al-Mn-steel (Steel A), 0.35 wt.% Al-Mn-steel (Steel B) and Mn-steel (Steel C) has been examined. With the increase in load these steels shows remarkable decrease in weight loss due to change in surface microstructure from austenite to ε or ά - martensit
Mat. Res.. Publicado em: 26/06/2017
-
7. Análisis de falla de los bujes del tornillo de una extrusora utilizada para procesar pintura en polvo
ABSTRACT This article aims to present the failure analysis of extruder screw bushings used for the manufacture of powder paint. Two bushings, one from the transition zone and one from the metering zone were selected to carry out the study. Chemical composition and microstructural analysis, hardness testing and a detailed analysis of the failed surfaces by vi
Matéria (Rio J.). Publicado em: 22/06/2017
-
8. Microstructure and Mechanical Properties of Borided Inconel 625 Superalloy
ABSTRACT The Ni- based superalloy Inconel 625 is extensively used owing to its high strength, excellent fabricability, good weldability and outstanding resistance to high temperature corrosion against aggressive environments. However, despite its unique properties and extensive use, its wear resistance is in some cases unsatisfactory. In this study, Inconel
Matéria (Rio J.). Publicado em: 22/06/2017
-
9. Influence of Tungsten on Dry Sliding Wear Behaviour of Sintered/Hot Extruded P/M Alloy Steels (Fe-C-W-Ti)
In the present scenario, Powder Metallurgy (P/M) is an established manufacturing process used to make components of complex geometries with high strength and tolerances by using incredible materials which are difficult to melt or form by other processes. The mechanical properties and microstructures will determine the component characteristic dependent on th
Mat. Res.. Publicado em: 08/06/2017
-
10. Blast Furnace Hearth Lining: Post Mortem Analysis
The main refractory lining of blast furnace hearth is composed by carbon blocks that operates in continuous contact with hot gases, liquid slag and hot metal, in temperatures above 1550 ºC for 24 hours a day. To fully understand the wear mechanism that acts in this refractory layer system it was performed a Post Mortem study during the last partial repair o
Mat. Res.. Publicado em: 15/05/2017
-
11. Fabrication and High Temperature Friction Behavior and Oxidation Resistance of Ni-Co-ZrO2 Composite Coating
Ni-Co alloy and ZrO2 micron particles were codeposited on 45 carbon steel by electrodeposition. The composition and microstructure of the composite coating were characterized. The high temperature tribological properties were carried out by a pin-on-disk tribo-tester. Additionally, the oxidation resistance was evaluated via high temperature circulating oxida
Mat. Res.. Publicado em: 05/04/2016
-
12. Rheological and mechanical characterization of poly (methyl methacrylate)/silica (PMMA/SiO2) composites
The search for new materials with properties suitable for specific applications has increased the number of research studies to fill the market demands. The development of polymer composites by the addition of inorganic fillers to the poly(methyl methacrylate) (PMMA) increases the potential use of this polymer in various application fields. The main objectiv
Mat. Res.. Publicado em: 01/08/2014