Weibull Modulus
Mostrando 1-12 de 19 artigos, teses e dissertações.
-
1. Glass-ceramic produced with recycled glass
ABSTRACT The objective of this work is the production and characterization of glass-ceramic with recycled glass powder and 4% (w/w) of cerium dioxide. Eleven groups were defined with conformation pressure of 11.6 and 25.8 MPa, and cerium dioxide addition. The sintering temperatures of 650, 675, 700 and 750 °C were used. The raw material was formed into a mo
Matéria (Rio J.). Publicado em: 25/11/2019
-
2. Microstructure and Weibull distribution of rupture strength of clay-talc ceramics
Resumo As propriedades mecânicas das cerâmicas de argila-talco contendo 0 a 10% em massa de talco sinterizadas a 1100 °C foram obtidas por medidas de flexão. Com o valor médio de resistência à flexão de 23,1 MPa, a amostra com 5% de talco (G5) foi a mais forte e apresentou o menor valor de poro interconectado (64%). A dispersão dos valores de resist
Cerâmica. Publicado em: 06/06/2019
-
3. Size Effects on Fracture Parameters of High Alumina Refractories
The randomness of phase compositions and their distribution as well as the micro cracks and pores in refractories result in the dependence of mechanical properties on the sample size. In this work, the size effects on fracture parameters including bending strength, elastic modulus and fracture toughness of high alumina bricks were investigated by testing sam
Mat. Res.. Publicado em: 10/07/2018
-
4. Effect of the Cooling Rate on the Properties of Veneer Porcelain for Zirconia Dental Prosthesis
To solve chipping of veneer porcelain in zirconia dental prosthesis it has been studied different cooling rates in firing schedules to control residual stresses generated by differences in thermal properties between the ceramics. However, cooling rates may affect the porcelain, irrespectively of interaction with zirconia. This study analyzed the effect of co
Mat. Res.. Publicado em: 07/08/2017
-
5. Reliability, failure probability, and strength of resin-based materials for CAD/CAM restorations
ABSTRACT Objective: This study investigated the Weibull parameters and 5% fracture probability of direct, indirect composites, and CAD/CAM composites. Material and Methods: Discshaped (12 mm diameter x 1 mm thick) specimens were prepared for a direct composite [Z100 (ZO), 3M-ESPE], an indirect laboratory composite [Ceramage (CM), Shofu], and two CAD/CAM co
J. Appl. Oral Sci.. Publicado em: 2016-10
-
6. Estudio de la estructura y las propiedades mecánicas en un recubrimiento de circona estabilizada con 8% en mol de itria elaborado por proyección térmica por plasma a partir de suspensiones
The study of nanostructured coatings manufactured by thermal spraying has generated a great interest in the last two decades due to their considerable improved properties especially in the physical and mechanical properties. This improvement is to reduce grain sizes of their raw materials at scales of 100-1000 times lower compared to conventional coatings (m
Matéria (Rio J.). Publicado em: 2016-03
-
7. Tensile Properties and Fracture Reliability of Melt-extracted Gd-rich Amorphous Wires
Gd60Al20Co20 amorphous wires with smooth surfaces and circular cross-sections were fabricated by a melt-extraction technique. The mechanical properties of the extracted microwires were evaluated by tensile tests and their fracture reliability was estimated by using Lognormal and two- or three- parameter Weibull analysis, respectively. The microwires exhibit
Mat. Res.. Publicado em: 17/11/2015
-
8. Fique Fiber Tensile Elastic Modulus Dependence with Diameter Using the Weibull Statistical Analysis
Fique is a plant native of Colombia with fibers extracted from its leaves presenting relevant physical characteristics and mechanical properties for possible engineering applications, such as reinforcement of polymer composites. The main physico-mechanical properties of the fique fiber have already been investigated for both untreated and mechanically treate
Mat. Res.. Publicado em: 23/10/2015
-
9. Durability under thermal loads of polyvinyl alcohol fibers
In the present paper, the thermal durability of polyvinyl alcohol fibers (PVA) was studied after fiber samples had been subjected to temperatures ranging from 90°C to 250°C. Residual mechanical properties, such as tensile strength, elastic modulus and elongation at break, and physical properties, such as density were determined. Weibull statistics were use
Matéria (Rio J.). Publicado em: 2013-12
-
10. Surface agents' influence on the flexural strength of bilaminated ceramics
The objective of this study was to evaluate the influence of different surface agents on the flexural strength of a ceramic system. Eighty bar-shaped specimens of zirconia were divided into four groups according to the agent to be used: group Control - to be cleaned with alcohol; group VM9 - application of a fluid
Braz. oral res.. Publicado em: 2013-07
-
11. Weibull analysis for the diameter dependence of the elastic modulus of curaua fibers
The curaua fiber is one of the strongest lignocellulosic fibers and is currently being considered as reinforcement of polymer composites for industrial applications such as automobile interior components and bicycle helmets. The tensile strength of the curaua fiber was found to display an inverse variation with its corresponding equivalent diameter. Since th
Matéria (Rio J.). Publicado em: 2013
-
12. COMPARAÇÃO DE DIFERENTES ENSAIOS MECÂNICOS PARA AVALIAR A RESISTÊNCIA ADESIVA A UMA CERÂMICA Y-TZP / COMPARISON OF DIFFERENTS MECHANICAL TESTS TO EVALUATE THE BOND STRENGTH TO A Y-TZP CERAMIC
This study aimed to evaluate the bond strength using different test types for bonding evaluation, between a yttrium tetragonal zirconia polycrystals (Y-TZP) ceramic and composite resin, considering two types of Y-TZP surface treatments. Three hundred and sixty Y-TZP blocks, received one of the two surface treatments (N= 180): UT- control (untreated) and SS-
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 23/03/2012